Dress can be made from cotton or silk fabric in small patterns or plain (sizes 46 - 54). 

The bodice at the waist line attached. Front bodice with undercut from the armhole (i.e., the shoulder tuck moved to the line of openings), continuing below the waist line. The undercut ends with peplum, passing into the valve, which is fastened to the skirt with a button. Back telekrona with a seam in the middle. In tuck stachen strap, fastened with a single button. Vtachnoy sleeve, three-quarter. Collar with rounded ends, slightly behind the neck. Finish - bow and buttons.

Dress this style particularly suits women with narrow hips, as unfastened peplum-valve widen the hips. 

Drawing style lines on the pattern (Fig. 46) 

a Style developed by the pattern of the basic drawing dresses. 

 3аднее flag (Fig, 46). To expand the neck of the sprout at the shoulder cut into 3 cm (optional). Part of the Darts to move to the middle of the back of the cloth. This waist right to postpone 1 cm and a tuck to reduce the 1 cm hem Line from the middle of the back of the cloth to extend 2 - 3 cm, point 1 is connected with the neck of the sprout, then raskladam bottom line. Side-cut hem to defer to rasciesa right 3 - 4 cm 

 Strap. From the waist up and down to lay 2.5 cm From 2,5 to draw a line parallel to the waist line, to the middle of the Darts and the waistline by 2.5 cm, to issue mysyk length 2.5 cm, 

 Front panel (Fig. 46, b). To expand the neck at the shoulder cut of 3 cm To move the shoulder Darts in the armhole divide it into three parts and from the top of the division until the end of the shoulder tuck to hold the line. For indentations at the waist from center front cloth to defer to the left of 1.5 cm and bottom line right 3 - 4 cm Points of 1.5, 3 to 4 and the neck connect. For entry of fasteners from the depth of the neck down to postpone 6 - 8 cm, right 3 - 4 see Connect the dots, as shown in Fig. 46 b. 

A tuck at the waist to reduce by 1.5 cm. the Ends of the shoulder tackle and Darts to join.

 The design of the barrel valve (part III). From waist line for side cut and tuck down to lay 9 see the Cut from the side of the slice to tackel tuck to split in half, and then from the points of division delay down to 15 cm, 15 Points, 9 splice, as shown in Fig. 46 b. For rascles bottom line to delay the left 5 cm, Points 5, 9 connect. 

 Collar (Fig. 47,) To build a collar to measure the line terminations (cut the sprout and the neck). To construct a rectangle with length equal to the line terminations, i.e. 25 cm, width 10 cm From the top right corner down to postpone 2 see Points 2, 10 to connect a smooth line. 

The parts are numbered and show the direction of the grain lines. 

Obtaining the modified pattern and cutting (Fig. 47) 

 3аднее panel (see Fig. 46, a) be cut out of the pattern. The backrest can be done with seam and without seam. 

 The front panel (Fig. 47). For applying the pattern lines to cut. Shoulder tuck to close, whereby the opening of the new tuck through the openings. Part of shoulder Darts to move to the side cut. To do this, cut the pattern from the side of the slice to the end of the shoulder tuck. 

For separation of the valve barrel from the front cloth skirts under the pattern to enclose a blank sheet of paper and translate the cutter, then cut out on the fabric. 

For the correct connection details to get the checkpoint. 

 The flank with valve (Fig. 47, b) to find on the pattern. For the treatment of valve to otkroite obtachku (shown in phantom).

 Collar (Fig. 47). Upper and lower collar cut out on the bias thread. 

 The strap (Fig. 47, g) translate the cutter from the pattern. To do this, to put under her sheet of paper and then find the tab on the fabric. 

The seam shown in Fig. 47.
 

Tailoring 

1. To celebrate the middle of the valve, collar, and waist line cushioning seam. 

2. To lay a snare for the main lines and shaped patterns. 

3. To handle the loops on the strap and the valves (see here). 

4. Baste and sew the Darts in the tackle and the middle of the back of the cloth, at the same time vracheva belt (strap), the width of which in the finished form needs to be 4 - 5 cm 

5. To handle the valve barrel podkralas the facing folded them face inward, sew, make nadziejko in the corner to turn. To straighten the seam, releasing the roll from the primary by 0.1 - 0.2 cm, and priotity.

6. Baste and sew the front panel with sideways inseam. Below the waist line side to vacate tuck in the skirt, which in the middle of the Darts to make a cut equal to the line terminations. 

7. Baste and sew the middle of the front cloth of the dress. 

8. To process the closure for this allowance given for the setting of the fastener, the bend on the wrong side and attach manually. 

9. Baste and sew the shoulder and side seams. Shoulder seams to press into the side rear panels, side to side front cloth or resuturing. 

10. To votate and vacate collar at the neck (collar vacilate with a forward facing).

11. Baste and sew the seam of the sleeve, handle the bottom of the sleeves. 

12. To votate and vacate sleeves in armhole. 

13. Hem the bottom of the dress. To iron the dress, sew on buttons and attach the finishing bow.