The products of the highest quality garments, made of fine worsted and wool fabrics above 36 groups according to the price list No. 32. For the lining of these products apply to silk fabric with 1507 group and higher in price list No. 034. Applied materials and fittings must also be of high quality.
To the products of expensive fabrics must meet particularly high requirements that must be taken into account, especially when modeling, the selection of fabrics, finishing materials and accessories.
Top fabric, lining and butt should not only have a beautiful appearance, but also meet requirements to technical requirements. Thus, the shrinkage of these tissues should not be above the norms for shrinkage GOST 11207 - 65 for fabrics of the first and second groups.
Side of the fabric should be wool or wool blend duck or a type of fabric art. 10114, 10121, 10122.
As warming pads in the winter coat you need to apply wool or wool blend batting.
For finishing winter coat used only a valuable fur.
Burlap trousers are made from a fabric type TEC-eraser.
Allowed the use of adhesive materials using a polyamide spot coating.
In designing the highest-quality products provide increased size of the technological allowances (table. 9).
Table 9 the Size of the technological allowances in the highest-quality products
| Name of the allowances of the parts |
The margins in the patterns of products, see |
| jacket |
jacket |
pants |
skirt |
coat |
| men's |
women's |
| Width of bending the bottom of the products |
3,0 |
3,0 |
4.0 (with no cuffs) |
5,0 |
4,0 |
4,0 |
| Width of bending the bottom sleeve |
4,0 |
4,0 |
- |
- |
4,0 |
4,0 |
| The width of the bottom podborta products |
Not less than 8,0 |
Not less than 8,0 |
- |
- |
Not less than 8,0 |
Not less than 8,0 |
| The width of the seam allowance at the top of each of the middle seam of the rear halves of the pants |
- |
- |
3,0 |
- |
- |
- |
| The width of the allowances of the side seams from the shelves, the elbow joints from the lower halves (top to the elbow) |
2,0 |
2,0 |
- |
- |
- |
- |
Notes:
1. Products in the flared width of the bending is done according to the model, but not less than 3 cm In the women's coat with lining, pricechannel on the bottom allowed width of bending the bottom of the 3.0 cm
2. Podborta bottom width, measured at the level of the bottom hinge.
In handling products of the highest quality compared with the processing of tissue 36 below the list the group has the following characteristics.
Pocketing. In the men's products in the burlap right side pocket handle additional pocket for little things (see here) womens coat the side pockets definitely handle interior pocket (see here).
Processing of side edges and edges of collar. Jackets, jackets and coat lapels after the stitches and the ends of collar bottom cover additional gasket. The inner edge of podborov in men's coats edging of lining fabric or tape. In podborta allowed one extension with the placement of the seam at the top below the first loop on the side down at a distance of not less than 6 cm, vest at least 8 cm from the bottom. In a single-breasted jacket with a clasp on 3 buttons, the seam should be located below the second hinge.
Processing insulated strip. In womens winter coats batting covered with gauze. When connecting to the product strip is placed gauze down.
The definition of quality. Products of the highest quality in finished form shall meet the requirements MRTU 17-760-69 "Products of the highest quality", and approved model. The quality of the product should not be below the first grade in accordance with GOST 12566 - 67 "sewing for household purposes. The grade".
Products that do not meet these requirements translate into the category of items of mass tailoring the appropriate price list.
| 