Processing belt and strap without pads. The belt can be cut in two parts with the location of the seam in transverse direction on the line side seams of the dress. 
Part of the fold belt, right sides inside, equalizing sections, and grind off. Joint width of 0.5 - 0.7, see the articles of wool and silk fabric seam rautureau, and for products made of cotton fabrics spread, displaying on two sides.

Belt and strap consisting of a single part, bend along the middle of the front hand inside and grind on three sides (Fig. 24, a), leaving the middle hole for the reversing length of 2 - 3 cm, or not to grind one end (Fig. 24, 6). 
In the belt or strap, the ends of which stachivaya in the side seams or Darts, these tips don't grind andturn through them in detail.
After grinding the seams in the corners cut, leaving a seam allowance of 0.2 - 0. see using a special fit belt turn on the front side, straighten seams the articles of silk and woollen fabrics, spawn, positioning seam atbending or forming, edge width 0.1 cm (depending on model), and priorivet. The belt can be processed by zatrachivaniya with ACC the cut edges inside.
Zatrachivaniya produce on all sides a distance of 0.1 - 0.2 cm from the edge. Allowed to prithwijit belt without the buttonhole edges, forming and consolidating Kang in the process of wet-heat processing. Prutivka perform from podmotsa through the gasket. Left the hole for turning is sewn manually hiddenblind stitch stitch length 0.2 - 0,ZSM. Neobychny the end of the belt zastrugivajut on the sanding machine at a distance of 0.1 - 0.2 cm from the edge (Fig. 24). 

  Processing of hard zones.Hard the belt is treated in the same sequence as the soft, but for eversion leave neobychnym one end of the belt. Belt turn with the help of a special device at the same timeinvesting inside grosgrain ribbon to the desired width (Fig. 25,a). Grosgrain the tape should be 0.2 - 0.3 cm shorter belt. In this case seams are located between the bottom side of the belt and grosgrain ribbon. Belt priorivet through the gasket. ~oneTs belt zastrugivajut with bending sections the main material inside the waist and without bending, butgrosgrain ribbon was not visible from the front side.
In the absence of grosgrain ribbon strip belt cut from a tough cotton fabric or proklamelin. The strip of fabric applied to the underside of the bottom belt parts, combining one of the equity slice of the strip with the fold line at the width of the belt, and pritachivajut the entire length of the belt on one line a distance of 0.5 cm from the fold (Fig. 25, b). If the belt is wide, lay two lines. Then fold the waistband along the middle front inside and grind. Seam width 0.5 - 0.7 cm, a strip from the seam carving, belt turn on the front side (Fig. 25).
Further processing of the belt is the same as described above. 
When processing belts with the pad of proklamelin the gasket is applied on the underside of the top of the belt and the strip of fabric, and attach with pins in three or four places. Belt bend in half along the length of the face inward, equating slices and grind on the lower part of the belt, under the line hits the pad ofproklamelin, pins removed, the gasket seams cut, belt turn on the front side and are treated the same way as above. 
  Processing end of the belt with belt loops. The belt loops are folded in the middle along the width of the face inside, equating slices, and grind a distance of 0.5 - 0.7 cm slices, then turn out, straighten the seam, placing it on a fold, or form Kant on the inner side of a width of 0.1 - 0.2 cm and priorivet.
When processing narrow loops of thick fabric, belt loops along the fold in the middle of its width with the wrong side inside, and equity sections to buckle at 0.5 - 0.7 cm depending on the width of the belt loops and zastrugivajut on the edge. On the second the edge depending on the model or the thickness of the fabric can be laid finishing line at the same distance as when zatrachivaniya slices.

If the belt loops are wide and designed instead belt buckles, in this case the finishing line on the second edge of the belt loops paving required. Belt loops fold double face inside, equalizing sections, and sew on a distance of 0,5 - 0,7 cm from slices, seam rautureau (Fig. 26,a) or for strength rasstraivaet, attaching sections of the seam to the inside of the belt loops. Belt loops turn on the front side.
Belt loops put on the table wrong side up, positioning the seam stitching in the middle. Inside the loop putthe raw end of the belt by 0.7 - 1 cm facedown scribbled edge loops on the inner side of the belt (Fig. 26, b), by bending the outer part of the loop, so it does not fall under place. Width the seam from the belt loops of 0.2 cm, the waist of 0.7 cm Processed the end of the belt threaded through the belt loops, straightening the seam felling loops on the belt and set the belt inside the belt loops. Then scribbledsecond, the inner edge of the belt loops on the waistband at 0.2 cm from the edge (Fig, 26), also by bending the outer part so that it does not come under line.
  Processing end of the belt buckle. In a buckle threaded the raw end of the belt, round the middle bar of the buckle, pass the end of the belt in the direction of the bottom 2 to 4 cm and zastrugivajut by car around the middle rail and edge bending slices 0.7 cm (Fig. 26,g), or fastened in a special fixture metal eyelets. In the individual production allowed hem the end of the belt by hand slanted stitches with a length of 0.2 - 0.3 see Then in the belts, fastened with a buckle, special the punched fixture holes and treat them with blocks.