Jumpsuit (Fig. 292), consisting of bodice and pants, suitable for children of preschool age. The front half of the Romper, one-piece, in the middle of the front pocket. Back waist cutoff, and button placket.
The fabric is thick cotton.
The drawing pattern removed following measurements in inches:
The semicircle of the neck ... 12,5
"the chest ... 28
"waist 28 ... 
"thighs . .30
Back length to waist .... 25
"shoulder................... 8
"pants............. 55

Construction drawing of the front half of the Romper
 

 Bodice. Draw a rectangle АТВТ1 (Fig. 293, a)
The vertical sides are equal measure the length of the back: at=VT1=25 cm.
The horizontal side is equal to 1/2 of the semicircle of the breast plus 3 inches: AB = ТТ1 = 28: 2 + 3 = 17 see
  the depth of the armhole. From point A to defer down 1/3 of the semicircle of the chest plus 4 cm, to put the point G: AG = 28: 3 + 4 = 13,3 cm
From point G draw a horizontal line to the intersection with the vertical, to put the point G1.
  The width of the front. From the point G1 on line ГГ1 to postpone 1/3 of the semicircle of the breast plus 3 inches and place the point G2: Г1Г2 = 28: 3 + 3 = 12,3 cm
From a point G2 to hold up the vertical line and the intersection with the horizontal to put the point A1.
  Width of the neck. From a point In the delay to the line AB of the semicircle of 1/3 of the neck plus 1 cm plus 2 cm in width of the cut and put the point B1: BB1=12,5:3+1+2=7,2 see
  the Depth of the neck. From point b to delay down 1/3 of the semicircle neck plus 2cm and put an end B2.
BB2 = 12,5: 3 + 2 = 6,2 cm
To connect a smooth line points B2 and B1.
  Shoulder line. For slope of shoulder from point A1 to postpone down 1 cm From a point B1 through a point 1 to hold the shoulder line is 6 cm, and put a point P: В1П=8 - 2=6 cm
  Line openings. From the point G2 on the line that divides the angle in half, put 2 cm to Hold a smooth line from the point P to points 2 and G. Outline of the pocket, as shown in the drawing.
  The front half of the pants. A vertical line from the point T to continue down the length of the pants - 55 cm and put the H-point. From the point N to the right, draw a horizontal line equal to 1/2 of the semicircle of the hips, plus 5 cm, and put the point H1. From point H1 to hold up the vertical line with a length of 55 cm and put an end T2; points T1 and T2 to connect a straight line.
Line НН1 split in half and the dividing point to hold up straight line to the intersection with the line ТТ1 to put the point T3. From the point T3 to postpone the right depth of folds equal to 2 cm
  Line width of the step. From point T to postpone down 1/2 of the semicircle hips plus 3 cm, to put the point W. From point W to hold right horizontal line to the intersection with the line Т2Н1 and put an end SH1: TS = Т2Ш1 = 30: 2 + 3 = 18, see
  the Line of the front joint. From point T1 to hold down a straight line to the intersection with the line of step, to put the point B. From point B postpone up to 3.5 cm, and this point to connect a smooth line with a point SH1.
  Width of the bottom. From the dividing point on the line НН1 to defer to the left and to the right at 6 cm and put the points N2 and N3.
  Line of the side seam. Point H2 and ø to connect a straight line.
  A line step length. Points H3 and SH1 to connect an auxiliary line to divide it in half. From the points of division to defer to the left of 0.5 cm and a smooth line connecting the points D3; 0.5 and SH1.

Construction drawing of the rear halves of the Romper

  Bodice. Draw a rectangle ВАТТ1 (Fig. 293, b).
To build the upper part of the bodice as well as the bodice front, with the exception of the depth of the neck.
To build the depth of the neck to defer from that point down 1/3 of the semicircle of the neck, to put the point Q3: ВВ3 = 12,5:3 =4.2 cm
To connect a smooth line points B3 and B1.
To build the lower part of the bodice as follows. From point T to postpone down vertical 11 cm From the point 11 to be postponed to the left horizontally 1.5 cm Point 1.5, and T to connect a smooth line. From point T1 to delay down 5 see Point 1.5 to 5 and connect auxiliary line to divide it into three equal parts.
To hold the hem line of the bodice from point 5 to point to 1.5, as shown in the drawing.
To clasp the bodice to postpone the left from points B3, and 5 to 2 cm and point 2 are connected by a straight line. Outline loop, as shown in the drawing.
In the middle of the waist outline the crease with a depth of 3 see
  the Rear half of the pants. Draw a rectangle ТТ2НН1 (Fig. 293"). Vertical sides equal to the length of the pants.
Calculation of the vertical sides and horizontal sides of the rectangle and the line of the step is the same as for the front half of the pants.
  The bottom line. Horizontal line НН1 split in half. From the dividing point to hold up the vertical line and, continuing her waistline by 1.5 cm, to put the point T4.
From the dividing point on the line of the bottom to be postponed left and right 7 cm and put the points N2 and N3.
  The waist line. Continue to the right line ТТ2. From the point T4 to draw a line equal to 1/2 of the semicircle waist plus 2 cm (in a tuck) to the intersection with the continued horizontal line and put a point T5, Т4Т5 = 28: 2 + 2 = 16 cm.
From the point T4 to postpone the left 3 cm and put an end T6. At the midpoint of the segment Т4Т5 outline the tuck as shown in the drawing.
  Line of the side seam. To connect with a straight line points T5 and H3.
  The extension of the pants line width of the step. From point W to be postponed to the left horizontally 1 cm and 1/5 of the semicircle of the hips, to put the points B and B1: BB1 = 30: 5 = 6 cm
  , the Line length of the step. Connect the dots D2 and B1 of the auxiliary line. To postpone it Н3Ш1 length (see Fig. 293, a) and put a point B2 (see Fig. 293,). Divide the length in half and Н2Б2 from the points of division to defer to the right of 0.5 cm to Connect the smooth line of a point of H2; 0,5; B2.
  Line the back seam of the pants. From point W to defer up 1 see Connect the dots B2, B, 1, and T6 smooth line, as shown in the drawing.

Prepare a pattern, layout and cutting
 

To prepare the pattern belt length 24 cm (semicircle waist minus 4 cm), width 2.5 cm to make a Copy of the pattern pocket
Lay the pattern on the fabric, as shown in Fig. 294, and find.

Tailoring

Baste and sew a seam in the middle of the front of the overalls to the line step length. To pristroit pocket. To oblachat bias binding the hem of the back bodice to the waist. Bend allowance for the zipper inside out and stitch.
Sew shoulder and side sections of the lapped seam. To oblachat the neckline and armhole with bias binding. To stitch folds at the waist. Baste and stitch a tuck on the rear half of the pants. Sew seams along the lines of the length of the step and sides. Sew back seam of the pants. Hem the bottom of pants. Sew the waistband to the waist line of the rear halves of the pants. The ends of the belt to stitch separately. At the ends of the belt and in the middle of the back sweep of the loop. Sew on buttons.