Dress of plain wool or silk cloth (sizes 48 - 60), one-piece. 

Off the shoulder is a deep tuck. 

The back is straight with shaped Darts. 

Vtachnoy sleeve, three-quarter. 

Collar - telekrona stand with two soft pleats at the neckline. 

This style of dress can be recommended to all women, especially for full figures. 

Drawing style lines on the pattern (Fig. 115) 

the Feature is designed according to the pattern of the basic drawing dresses. 

 The rear panel (Fig. 115). The height of the sprout up to 4 cm delay Line the middle of the back of the cloth to continue up to the level of point 4. From point 4 draw a line to the intersection of the obtained line. From the point of intersection down to postpone 1 cm and place tselnokrajnie rack, as shown in Fig. 115.

To obtain two notched recesses required for side cut of the waist line to the right to allow for the width of the second tuck, i.e. 2.5 cm From the middle of the back of the cloth at the waist line to the right to defer half the distance between the Darts, i.e. 7 cm. From point 7 the right to postpone the depth of the tuck (2,5 cm) to build it, length of back 13 cm, while the skirt 15 see Then leave the distance between the Darts 2.5 cm and from the point of 2,5 - depth second tuck (2.5 cm).To obtain a figure darted from the tips of their right to postpone for 3 cm and point 3 to connect with deep tucks at the waist a smooth line, as shown in Fig. 115.


 The front panel (Fig. 115, b). From the top of the neck up to postpone the height of the stand, i.e., 4 see plotting points to connect. Line the middle of the front to continue up to the intersection with the line height of the rack. The depth of the shaped neck at the middle of the front must be equal to 6 cm and the width of the top line one the other side by 1 cm to Make the rack and the cutout, as shown in Fig. 115 b. 


In the neck in the middle of the front to cause the depth of soft folds and the distance between them, i.e., from point b down to postpone 6 cm (2 cm crease and a 2 cm distance).


To get a drape side section and the right-traveling tuck, transfer the shoulder dart to the waistline. For the side cut of the right cloth at the waist to apply a cutting line to tackle the tuck and the end of it to connect with the end of the shoulder tuck. To gain a deep tucks from the right shoulder to cause the cutting line of the first line shoulder tuck by the end of it on the left panel, extending this line up to the side of the slice. 


Obtaining the modified pattern and cutting (Fig. 116)

Lines for applying a pattern to cut the side cut of the right cloth to the end of the shoulder tuck, not dorezaya 0.5 cm Shoulder tuck to close, whereby the opening of the new tuck on a lateral slice will increase traveling for draping, then cut the pattern from the shoulder cut to the side, not dorezaya 0.5 cm Shoulder tuck on the left panel to close and take the pattern up to 15 - 16 cm Side cut on the right panel to find a straight line, as shown in Fig. 116. 

The seam and stocks is shown in Fig. 116. 

Tailoring

1. To celebrate the middle of the front and rear panels of the cushioning seam. 

2. To lay a snare for the main lines and shaped patterns.

3. Baste and sew the pulley-block tuck on the rear and the left front panel.

4. To underside of right shelf tack the facing width 4 5 cm and length equal to the length of traveling block tuck on the right panel. To prometti and lay the line in the middle of the Darts, and then in the other side of it at a distance of 0.5 cm one line, then preteroti the lace and pull the excess fabric to the position normalnoi the length of the tuck. To prepare rulik oblique piping length 25 - 30 cm and a width of 0.5 - 0.7 cm. To knit the bow and attach it to the end tucks on the skirt. 

5. Baste and sew the shoulder tuck, in the end leaving a soft pleat and pin her cross stitching.

6. To gather the Assembly for the side cut on the right panel.

7. Sew the soft folds in the neck (the length of the line from the middle of the front cloth in one and the other side for 2 - 3 cm). 

8. Cut the back panel of a dress in the middle. Cut length equal to the length of the lock minus 1 - 1.5 cm Process-section of the fastener with a facing width of 8 - 10 cm and length equal to the length of the castle, "lightning" plus 4-5 cm 

On the front side of "lightning" to impose the underside of the processed section of the zipper, baste and Topstitch to the desired width of the lines from the edge of the treated section.

9. Baste and sew the shoulder and side seams shelves and back. 

10. Processing rack podkralas the facing. For this sew piping front and back panels at the shoulder cut, stitch resuturing. To attach the facing face to the front of the unit, pritchet seam width 0.7 cm, nadsech a breakdown in the middle of the front cloth, bend towards the inside, prometti, releasing the roll from the side products by 0.1 - 0.2, see Second section of piping to bend in the direction of the inside of 0.7 - 1 cm, blaze line 0.1 - 0.2 cm from the fold and attach to the product manually in several places.

11. Baste and sew seams sleeves, handle the bottom of his podkralas the facing. 

12. To votate and vacate the sleeve in the armhole. 

13. Hem the bottom of the dress and ironed.