Dress from solid-color fabric or a small picture (size 48 - 56), one-piece. On the front panel below the chest line curly undercut, a challenge to the skirt. Through podraza at the top of the bodice and below the waist line draping (ruching). Back telekrona. Front double-button closure. Drapery in a curved undercut dresses can be modified, i.e. to put one deep soft crease. Sleeve one-piece, three-quarter. Collar - telekrona stand. 

A dress of this style is recommended on all pieces. Especially good for shapes with protruding belly.

Drawing style lines on the pattern (Fig. 98) 

the Style developed at the pattern drawing on the basis of tselnokrajnimi sleeve and gusset.

 3аднее panel (Fig. 98, a). To build a collar, as shown in Fig. 98, and. 

 The front panel (Fig. 98, b). Continue shoulder cut in the side middle shelves are 3 cm From the points obtained up to postpone 1 - 1,5 see Connect point 1 and 1.5 with a shoulder cut.

From the depths of the neck to delay down 8 - 10 cm and draw the neckline, connect the dots of 1 - 1.5, 8 - 10. The length of the shelves, from the bottom of the neck to the waist line to divide in half, and from the points of division to delay down 2 see Wireline tuck to move it 2 cm closer to the middle of the front. Draw a line curly podraza, connecting point 2 to the end of tackle Darts smooth line. The end of the side tuck to move to the undercut as shown in Fig. 98 b.

To obtain soft Darts on the shoulder width and angled undercut on the shelf to divide it into three parts and cause cutting line pattern from figure podraza to the side of the shoulder. From the neck to podreza to add 2 cm to the middle of the shelves for the call of the clasp. From the waist down second side of tackle Darts split into three parts and cause cutting line pattern from darted towards the side of the slice. 

Obtaining the modified pattern and cutting (Fig. 99) 

 3аднее cloth to cut out on the pattern. The seam along the side and shoulder sections of 2 cm in the sprout 0.5 cm, hem 5 - 6 cm.

 The front panel (Fig. 99). For applying the pattern lines to cut. The side tuck the bodice to close, whereby the opening of the new tuck in undercut from the middle shelves. For the formation of the soft folds of the pattern caused by the lines from figure podraza to the side of the shoulder cut to cut, not dorezaya 0.5 cm (so as not to disturb the shoulder cut), and details of patterns of bodice to take up to 3 to 4 cm For the formation of soft folds on the skirt for applying the pattern lines to cut, not dorezaya to the side of the slice 0.5 cm, and take up the pattern of the bodice by 4 - 5 cm.When cutting the front panels of the dress the middle of the pattern to put the common thread to the bend of the fabric.

The seam and stocks is shown in Fig. 99.
 

Tailoring 

1. To celebrate the middle of the back and front panels of the dress cushioning seam. To note checkpoint patterns for combining slices. 

2. To lay a snare for the main lines and shaped patterns. 

3. Baste and sew the Darts on the back. 

4. The allowance of cloth given when cutting for machining of contoured lines podraza on the shelf, bend towards the inside and promette. On the put the lines on the bodice and skirt to lay soft folds, to connect the right shelf on the left the zipper. To impose the lower part of the bodice on the top, combining the traps and checkpoints.

5. Baste shoulder and side seams of the back and shelves to make the fitting. In fitting to specify the place and the position of the soft folds at the bodice. 

6. The lower part of the bodice to attach through podraza to the top, take the excess fabric at the waist in the undercut and pin, and then lay the soft folds on the skirt. 

7. After trying to move all of the patches on the right shelves on the left. 

8. Handle loop on the right shelf with one facing.

9. To the front side of the backrest applying face facing the rack, tack and pristroit 0.5 cm from the upper edge of the rack. To the front of the shelves to make face podborta, tack and pritchet 0.5 cm from the edge.

10. Baste shoulder seams of the bodice, propositiva back, at the same time to sweep away the seams piping and podborov. Sew a seam the shoulder seams of the piping and podborta, remove the basting. To resaturate seams piping with podborta and shoulder, straightening the seam. Sweep the edge of the stand, releasing the chute at the front side of the backrest and shelves. The second section of piping to bend to the inside by 0.5 cm pritchet 0.2 cm from the fold and attach to the product. 

11. Shaped line podraza sew to the underside of the bridging machine stitching in the corners manually.

12. Baste and stitch lower sleeve seams and side seams of the back and shelves to the next checkpoint. To votate and vacate gusset, aligning the reference point. Sew on the back and shelf without taking thread. Undercuts in the corners of the backrest and shelves line to nullify (by 0.2 - 0.3 cm from seam). The gusset is recommended to perestroit from the front side of the silk thread to match the product. The seams for the gusset fold in the side of the product, priotity, then pristroit at the front of the unit, retreating 0.1 - 0.2 cm from the seam vrachevanie gussets.

13. To handle the bottom of the sleeve facing podkralas, whether in equity or cross thread. The width obtachki 4 - 5 cm, its length equal to the width of the bottom of the sleeves plus 2 cm for the seam. Sew the ends of otacek, the seam grinding to resaturate. Tack the facing face side to the front side of the bottom of the sleeves, equalizing sections, and pricecat the facing seam with the width of 0.5 cm Seam primaqiune to resaturate. Fold the facing towards the inside of the sleeve, releasing the roll from the sleeve by 0.1 - 0.2 cm Pin roll slanted stitches.The second cut edge of the piping to bend towards the inside by 0.5 cm and pritchet, departing from the fold to 0.2, see the Facing to attach to the sleeve of concealed stitches. Slightly priotity it, remove the basting and iron from the piping until it is tight.

14. Hem hem, to iron.