Dress made of colored silk or cotton fabric (sizes 48 - 60). 

Front panel one-piece with insert, the top of which is laid in soft folds. 

The middle of the front to Pedraza on the skirt with the zipper. 

Casting wedge're slightly. 

The rear panel of the three wedges. 

Side seams at the waist line cutting. 

For slim figure can be prioraty, and the full back panel is good to do a one-piece. 

Vtachnoy sleeve, three-quarter. 

The collar is a small stand telekrona. 

A dress of this style can be recommended proportionally built and full women.

Drawing style lines on the pattern (Fig. 130) 

the Style developed by the pattern of the basic drawing dresses. 

 3аднее panel (Fig. 130, a). To build tselnokrajnie rack. To do this, the height of the sprout defer up to 2.5 cm, middle of the back to continue to a level with the point of 2.5, the obtained point linking. From the point of crossing and at point of 2.5 to be postponed for 0.5 cm to Make the rack, as shown in Fig. 130.

The width of the cut sprout at the shoulder cut right to postpone 6 cm and the resulting point to connect with the end of the pulley-block Darts. From the point 6 to the right to defer the width of the tuck (1 cm) and from point 6 down the length of her (7 - 8 cm). Points 1, 7 and 8 to connect. Apply a line of rasciesa wedges, for which line of tackle Darts continue down to the intersection with the bottom line. The line of the cut side of the wedge extends from the side of the slice to the pulley-block Darts.

 Note. The width of the wedge at the shoulder cut can be already, i.e. 4 cm (optional). To highlight the waist, a contoured line at the shoulder cut is wider (i.e., it creates the appearance of a narrow waist). 

 The front panel (Fig. 130, b). To build tselnokrajnie rack. Shoulder cut from the top of the neck to the right, continue for 1 cm and from point 1 up to postpone 2,5 cm 2,5 Point to connect with a shoulder cut, as shown in Fig. 130 b.

To apply a line of cutting inserts. To do this, from the waist up in the middle of the front to postpone 16 cm down to 13 cm and Then from point 16 to hold the line to the left at a right angle to the middle of the front cloth to the intersection with the line tuck. From the points 16, 13 the right to postpone 2 - 2.5 cm for the call on the closure. Plotting points to connect. Draw the neckline, connect the dots 2,5 with the setting of the fastener.

To obtain assemblies (draping) on the shelf to put cut lines from end of shoulder Darts to podraza. The width of the shoulder cut of the first line, Darts to the top of the neck split in half and the dividing point down parallel to the first line of the tuck to hold the line until podraza. 

For the best fit of gown to build a second dart at the waist line. For this traveling tuck divided into two with a depth of 2 cm One to leave the place, the second to move closer to the side cut.

Apply a line of rasciesa wedges on the skirt front cloth of the dress, continuing the line of tackle Darts down to the intersection with the bottom line. 

Pattern pieces are numbered and show the direction of the grain lines. 

Obtaining the modified pattern and cutting (Fig. 131) 

For applying the pattern lines to cut. To keep the basic lines of the pattern, along the lines of rasciesa wedges to cut her teeth or to remove separately each wedge cutter, tucked under a pattern a clean sheet of paper. 

 3аднее flag (Fig. 131, a, b, C) be cut out of the obtained parts patterns. The side wedge skirt (item 3) at the waist to allow for Assembly of 4 - 5 cm depending on the figure. On the full figure instead of an increase on an Assembly lightly to make the fit of the wedge at the waist or to carve out a wedge tselnokrajnimi. To find the facing for processing rack backrest common thread (podkraj shown by hachures). 

 The front panel (Fig. 131, g, d, e). For obtaining draping (assemblies) through podraza (part 4) caused to the lines of the pattern to be cut and push for 6 - 8 refer To the correct connection details to put control points on the waist line. In the part 4 along the hem of the bodice to give allowance for seams and supplies 3 to 4 cm to allow fitting to raise or lower the line of podraza. For the same purpose to add more to the seams and to the workpiece 5.

To obtain ruched wedge (item 6) from the fold of the fabric pattern to put on 8 - 10 see more rasciesa bottom line to give an allowance of 5 cm and received a point to connect with the upper line. 

The seam shown in Fig. 131. 

Tailoring 

1. To celebrate the middle of the back of the cloth and the waist seam cushioning. 

2. To lay a snare for the main lines and shaped patterns. 

3. Waist side seams to the back to gather in the Assembly (item 3), baste, and sew them with the barrels of the backrest (item 2, item 3) at the waist, folding inside out.

4. Baste and sew the average wedge with side ranging from the shoulder cut to the bottom line, folding inside out.

5. Baste and sew the shoulder seams of the front and rear panels of the dress, neaten the slices to press the seam toward the back. In the fold stand shoulder seam to nadsech and resuturing. Baste and sew the piping in shoulder seams, the lower section of podkralas piping to bend in the direction of the inside of 0.7 - 1 cm, obtusate 0.1 - 0.2 cm from the fold and priotity. To attach the facing face side to the front side of the neck, aligning the middle of the back and shoulder seams, tack and pritchet seam width 0.7 cmResuturing the seam, fold the facing towards the inside, releasing the roll from the side products by 0.1 - 0.2 cm, sweep, slightly priotity. To attach the facing in several places to the dress. Remove the basting and iron until it is tight piping.

6. To assemble the Assembly of the lower section of the shelf (item 4) and the upper section of the middle wedge of the front skirt (part 6). 

7. Handle loop on the insert (item 5) one or two obrazkami. 

8. Handle fastener and pajustiku equity obrazkami or allowance given when cutting. 

9. Allowance for this when cutting the top and bottom sections of the inserts (item 5), to bend towards the inside, and prometti priotity, put it on a shelf and wedge, combining snare, tack and pritchet front side seam width of 0,7 - 1 cm silk thread to match the product.

10. Baste and sew the pulley-block tuck on the front panel of the dress. 

11. Baste and sew the side front panels (item 4) with insert and the shim (5, 6) bridging seam. 

12. Baste and sew the side seams of the front and rear panels of the skirt. 

13. Sew seams sleeves, handle the bottom of the sleeve facing the transverse width 4 5 cm 

14. Hem the bottom of the dress concealed stitches, to iron and to sew.