Dress of plain wool or cotton (size 50 - 62), one-piece. At the bottom of the dress finishes with one-sided pleat. From shoulder seam shapes the line is placed in the pocket with tselnokrajnie leaflets. The back is straight with Darts.

Vtachnoy sleeve, three-quarter. The collar is a small stand telekrona.

Slim women dress such style is recommended to sew is slightly fitted. For women with flat buttocks instead of the tucks on the skirt you can lay two soft folds or make a notched tuck.

Drawing style lines on the pattern (Fig. 37)

Style developed on the pattern of the basic drawing dresses (see Fig. 3).

 The rear panel (Fig. 37, a). By the middle of the pattern for one-sided folds to add 6 - 7 inches of the height of the sprout up to delay 3 to 4 cm and from point 3 to 4 to continue the line of the middle of the back to the level height of the rack. Plotting points to connect. Point. crossing down to postpone 1 cm and from point 1 to extend the upper part of the strut to the right by 1 cm From the stand height, i.e., points 3 to 4, right to defer 0.5 cm and place the rack as shown in Fig. 37.

 The front panel (Fig. 37, b). Shoulder cut to continue at the height of the stand ie 3 - 4cm, and up at a right angle to postpone 1 cm, to connect the point 1 smooth line from the shoulder cut. From the depth of the neck down to postpone the 7 - 8 cm From the points obtained the right to defer 8 - 9 cm and draw a line parallel to the center of the front panel to the bottom line. From the middle of the front right for entry of a fastener of the shelves to postpone 2 cm and draw a line parallel to the first line. Points 1, 2 connect a smooth line,as shown in Fig. 37 b.

The third part of the shoulder, i.e. the distance from the width of the neck to tuck, split in half and draw a line parallel to the first line of the tuck, and then by the end of it.

In dresses, fittings where the line goes into the pocket, it is necessary to reduce the depth of tuck by the waist line 1.5 - 2 cm and in accordance with this to change the length of the Darts on the skirt. Waist the distance from the Darts to the middle of the front cloth - 9 cm Depth: tuck on a shelf 2.5 cm, length 12 - 13 cm, skirt 6, see the rest of the Darts to make the side cut.

 The line of entry into the pocket. From the waist down the cut side to set aside 10 - 13 cm, and from the middle of the tuck - 6 see Point 6 to connect the auxiliary line with point 10 - 13. The resulting angle at point 6 split in half and draw a line of length 1.5 cm Width the entrance to the pocket from the side of the slice to the right 15 - 16 cm Height tselnokrajnie leaves from point 15 to 16 to 3 - 4 cm to Make a tuck on the skirt, as shown in Fig. 37 b. From point 3 to 4 to draw a line, parallel to the bottom line. Bevel leaves a pocket of 1 cm to Connect the ends of the shoulder tackle and Darts.

The parts are numbered and show the direction of the grain lines.

Obtaining the modified pattern and cutting (Fig. 38)

 3аднее panel (see Fig.37, a) to carve out a prepared pattern unchanged, marking the middle of the pattern to the fold of the fabric.

 The front panel (Fig. 38, a). By applying the line pattern cut, not dorezaya to the end of the shoulder 0.5 cm tuck Half tuck to move closer to the neck for soft folds, and the second part of it in the notched undercut. For processing of the slice-of-pocket to otkroite obtachku with burlap, which must be wider than the entrance line to the pocket on the 2 - 3 cm.

For processing fasteners in the middle front cloth cut below the waist by 2.5 cm, then do the undercut to the line entering the left shelves.

Podkraj to handle the neck to do after the pleat in the middle front of a panel already laid.

 The flank (Fig. 38, b) carve out together with the burlap pocket.

The seam and stocks is shown in Fig. 38.
 

Tailoring 

1. To celebrate the middle of the front and rear panels of the dress and the waistline seam cushioning.

2. To lay a snare for the main lines and shaped patterns.

3. Stock received due to the folds on the right and left panels of the dress, bend towards the inside. Baste and sew the pleat from waist line down by 25 - 30 cm and securing it in the end cross stitching.

4. Processing tselnokrajnie slip pocket, applying Podkayne the facing face to the front side of the leaves, and pritchet seam width 0.5 - 0.7 cm before the notch at the end of it. To make nadziejko in the corner, trim the excess fabric, stitch resuturing, the bend facing towards the inside, releasing the roll from the side products by 0.1 - 0.2 cm, prometti slanted stitches and priotity.

5. Sweep a soft tuck from the shoulder cut on the front panel of the dress and sew 5 - 6 inches away from it priotity bend and tuck to the side of the openings.

6. Allowance for this when cutting on a contoured slice of the part III, to bend towards the inside, lay on the flank, combining the roof and then tack iron the seam to the corner leaves the pocket. Then baste from the wrong side along the string and remove the original thread. To pritchet side to the dress, at the same time grinding off the burlap pocket. To lay the finishing line on a shaped line width of 1.5 - 2 cm, from shoulder cut and bringing the line to the waist line.

7. Baste and then sew the shoulder and side seams shelves and back, resuturing stitch and press shoulder seams towards back, side to side shelves.

8. Sew the seam of the sleeve, wool dress resuturing, and cotton - to press toward the front of the sleeve. To handle the bottom of the sleeves podkralas a facing width of 5 - 6 cm Sew the ends of obrazek and seam to resaturate. To attach the facing face side to the front side of the sleeve, equalizing sections, pritchet, stitch resuturing, the bend facing towards the inside of the sleeve, the second slice to bend the 0.7 cm and sew to the sleeve with hidden stitches. To votate and vacate the sleeve in the armhole.

9. Treating the neck. Sew piping Rostock and the neck at the shoulder seam and cut to resaturate. Stock received due to the depth of the folds, bend the front side, baste, and sew the seam of the piping and allowance for processing of the clasp. The seam resuturing. To pricecat the facing to the neck seam primaqiune to resuturing, the bend facing towards the inside, releasing the roll from the side products by 0.1 - 0.2 cm, and promette.

10. Hem hem, to sew and to iron dress.