Dress made from bright colored fabrics or small patterns (sizes 48 - 52), one-piece with a rectangular neck, the end of which laid soft folds.


Patch side parts of the skirt to form pockets, ending with PATA, at the bottom of which laid soft folds.


PATA attached to the dress buttons.


From pockets laid unilateral folds.


Back telekrona.

 
Vtachnoy sleeve, three-quarter and the cuff.


Cuffs and pockets wide topstitched finishing line.


Dress with a light insert.


A dress of this style is recommended for full and older women.


Drawing style lines on the pattern (Fig. 92)


Style developed on the pattern of the basic drawing dresses.


 The front panel (Fig. 92, a)


From the depth of the cut of the neck down to the middle of the front cloth to defer 13 - 15 cm and from the received point to the left 6 - 7 see the Top of the cap and the point of 6 - 7 to connect with the end of the shoulder tuck.


 The pocket


On the line side of the cut from the waist line down to postpone 11 - 13 cm from the waist line at the tuck down to 4 - 6 cm Obtained point linking, continuing the line to the middle of the pulley-block Darts. At a right angle relative to the line width of the down delay valve, i.e. 9 cm From point 9 to draw a direct parallel to the top line, and put 9 to the left To see the point to move the tuck, which remains on the valve.


The width of the skirt hem is split in half and the first line of tackle Darts connect with the resulting point of division bottom line. This will be the line of the cut valve pocket along with sideways. The side cut of the skirt hem to extend to 5 - 6 cm


 with the Cuff flaps (Fig. 92, b)


To build a rectangle with a length of 24 cm, equal-measure arm circumference plus 2 cm (22 + 2 = 24 cm), width 5.5 cm. From the point of 5.5 to defer up to 4.5 cm - the width of the upper cuff and draw a line parallel to the bottom lines. Point right to defer 4,5 2,5 cm Connecting point and 2.5 point of 5.5. On the other hand to defer to the left 2.5 cm and the given point to connect to the middle line, as shown in Fig. 92 b.


Obtaining the modified pattern and cutting (Fig. 93)


 Back panel to make the pattern the main dress. The bottom line is back the cloth from the side of the slice to expand to 4 cm

 Front panel (Fig. 93, a). For applying the pattern lines to cut.

From neck to end of shoulder Darts in the pattern (part 1) cut, not dorezaya 0.5 cm, close the shoulder tuck, and this will open a new dart in the neck.

On the line slit front cloth skirts allow for half the depth of the folds, i.e. 6 cm, and the burlap pocket 9 - 10 cm At the end of the burlap to make the cut, not dorezaya to the main line 0.3 cm.

Traveling tuck in the side parts 2 close. At the cut lines to add 6 cm to half the depth of the folds (on the valve). At the top of the crease to make the cut to the checkpoint.

 Burlap pocket (Fig. 93, b) to carve out the shape of the part 2.

 Note. This dress can be cut with extended waist at the back and no side seams on the skirt. The back needs to extend from the waist at 11 - 13 cm and when cutting the side sections of the front and rear panels of the skirt to combine. Rascles along the hem of the front and rear panels to remove.

 Cuff (Fig. 92, b). Unfastened portion of the cuff to put the fold of the fabric and cut out two pieces. To give allowance for seams on all slices at 1 cm to Identify the location of loops, departing from the slice of 2.5 cm.

The seam and stocks is shown in Fig. 93.

Tailoring

1. To celebrate the middle of the front and rear panels of the cushioning seam.

2. To lay a snare for the main lines and shaped patterns.

3. Baste and sew tackel tuck back the cloth, sautois them towards the middle.

4. Processing obecnie loop one or two obrazkami. The upper sections of part 2 (Fig. 93, b) oblachat Hessian of the main fabric to seam width 0.7 si. The seams in the corners to nadsech, leaving a seam allowance of 0.2 - 0.3 see Burlap to bend towards the inside of the product, sweeping up from the burlap, releasing the edge of the main part of a width of 0.1 - 0.2 cm to Pave the stitching on the edges of the pockets at a distance of 1 - 2 cm from the fold. From control points on the lines of the outer fold of the pleat allowance of fabric to bend towards the inside.

5. To impose a lateral detail on the front panel of the dress (item 1), combining the snare.

6. Baste and sew tackel tuck, at the same time grinding off the burlap pocket and pleat. From the front side to lay the finishing line on the crease, not a fold prestativa to the product. The width of the lines on the crease should be equal to the finishing line at the valve.

7. Baste and sew the shoulder and side seams.

8. The neck to lay soft folds.

9. To handle the sprout and the neck cross obrazkami. Shoulder seams of obcutek sew, the seam grinding to resaturate. Fold the facing and the dress inside out, aligning shoulder seams, tack, pritchet, the seams resuturing in the corners to nadsech, the bend facing towards the inside, releasing the roll by 0.1 - 0.2 cm from the primary part. The second section of piping to bend towards the inside by 0.5 cm, to stitch, departing from the fold of 0.2 cm and priotity. The facing to attach to the product at the shoulder seams, soft folds.

10. To handle the bottom of the sleeves. To prepare the cuff. Processing obecnie loop. Bend line to bend the cuff inside out. On the lower part of the cuff to put a strip of a thin fabric, 0.5 cm is the main part, against the loop strip to cut. The ends of the cuff sew the strip seam width 0.7 cm Seam stitching to resaturate, turn on the front side, straightening the seam, releasing the roll from the cuffs, sweep, priotity and hem loops. At the unfastened portion of the cuff to lay the finishing place equal to the width of the line valve. The line of the lapel to press the upper cuff.

In the lower cut of the sleeves through the elbow, stepping right and left 2 cm, to make the notch the width of the seam, i.e. 1 cm (Fig. 93). Cut bend on the wrong side and hem with hidden stitches. Sleeve width hem from nasechek must be equal to line terminations cuffs. The excess width along the hem of the sleeves to lay in soft folds on the top of the sleeve, the direction of which must be in the direction of the elbow.

Fold the front side of the sleeve with the underside of the cuffs, tack and pritchet on the sleeve. The second cut of the cuff to turn inside out and sew hidden stitches for the seam primaqiune her. Lapel cuffs fold on the front side.