Dress of a plain or small pattern fabric (sizes 48 - 58), one-piece, closure on the front panel. 

Back panel flared with inverted pleats.

Sleeve short casting. 

Collar sew-on brace ("collar"). 

A dress of this style are encouraged to complete proportionally built women. 


Drawing style lines on the pattern (Fig. 250) 

the Style developed by the pattern of the basic drawing dresses. 


 The rear panel (Fig. 250 a). For rocklee to apply cut lines to the depth of tackle Darts to the side of the cut to the bottom rear panel. 


 The front panel (Fig. 250, b). To reduce the depth of neck at 1 - 1.5 cm to form the mouth. From the chest line down the middle of the front defer up to 4 - 5 cm, i.e. the upper point of the length of the clasp. From the obtained point to draw a line of the slit pattern to the end of the shoulder tuck. To move the shoulder Darts in the side cut to divide it from the depth of the armholes to the waist line into three parts and the upper point of division to connect with the end of the shoulder tuck. 


 Collar (Fig. 250). To construct a rectangle with length equal to the measure of the semicircle neck plus 2 cm, width 18 cm width of the collar is divided into four parts and draw a parallel line. For registration of the ends of the collar from the bottom and top points of division to defer to the right of 4 - 5 cm Obtained point to connect to the midpoint of the division and the rectangle is a smooth line.
 

Obtaining the modified pattern and cutting (Fig. 251) 

 Back panel (Fig. 251, a). For applying lines to cut the pattern from the hem to the waist line, then in the side cut, not dorezaya 0.5 cm 

When cutting the middle of the back of the cloth to put the fold of the fabric, the side skirts aside for 10 - 12 cm for the formation of allowance for an inverted pleat. Half of the stock on the crease to make the fabric cut from the hem up to 30 - 35 cm, then the side of the outer fold of the pleat, as shown in Fig. 251.

The shape of the stock on the fold to cut out a wedge (Fig. 251, b) with width below 10 - 12 cm, top 6 - 7 cm Length of the wedge must be equal to the length of the slit, i.e., 30 - 35 cm 

 Front panel (Fig. 251,). For applying lines to cut the pattern from center front to the side of the slice. Shoulder tuck to close, whereby the opening of the new tuck in the side. When cutting the middle of the shelf from the neck to the line of Pedraza to put to bend the fabric and hem the pattern to take away from the crease tissue to the entry of the shelves at 7 - 10 cm (Fig. 251,). While in the middle of the shelves on the undercut will open the tuck depth 1 - 2 cm to Mark the middle of the right and left panels snares. The front panel to lay on the table in the unfolded state (Fig. 251, g).Due to the extra thickness of the fabric when cutting to the middle of the front of the right cloth to add 2.5 cm to the length of the shelves and carried by line to cut, retreating 0.5 cm for the seam.

 The facing - Kant (Fig. 251, d). To handle clasp the right shelves to otkroite finishing facing-edge with a length equal to the length of the incision of the front, plus 5 cm, width 14 cm handle length left shelves to otkroite also obtachku, equal in length to the first width 11 cm 

 Collar to cut out on the bias thread with the addition to the seams on all slices of 1 cm

Sleeves can be long or short squeeze. 

The seam and stocks is shown in Fig. 251.
 

Tailoring 

1. To celebrate the middle of the front and rear panels and a waist seam cushioning. 

2. To lay a snare for the main lines and shaped patterns. 

3. Baste and sew wireline and side Darts.

4. On the right shelf to handle 5 - 6 oblachnykh loops. 

5. To prepare finishing the facing. From trimming the edges of the piping to defer 5 cm (width Kant plus the seam allowance), fold the fabric inside out. The upper part of the piping prostrochit seam stitching to resaturate, turn on the front side, prometti, priotity.

6. At the end of the section of the front to make nadziejko to the right side shelves on the width of the sunset. 

7. The edge of the right side of the shelf to bend to the inside by 0.5 cm and iron-baste seam on the upper part of the piping, keeping the width Kant 2 see Then from the inside to stitch, fixing the line at the end of the section. Cut the edge of the lower part of the piping bend to the inside by 0.5 cm and stitch, departing from the fold of 0.2 cm Vs loops make the cut bottom of the piping, sew hidden stitches along the cut loops.

8. Process the Board left shelves separately cut the facing. To fold it with the product inside out and pricecat. In the corner of the seam width to nadsech, not dorezaya to line 0.1 cm Seam stitching to press in the direction of the cut. Stepping back from the seam stitching piping 4 - 5 cm, to make her bend, the second section of piping bend on the wrong side, sew hidden stitches for the seam primaqiune. 

9. Baste and sew the shoulder and side seams. 

10. On the back to handle the clasp facing or vacate lock "lightning".

11. To prepare the collar. In the lines to fold it inside out, to equalize the edging edge. Sew unfastened portion of the collar in the corners to make the notch, the seams resuturing, remove the collar on the front side and promette. Prepared collar vacate in the neck. 

12. To vacate sleeves. 

13. Hem the bottom of the product.