Dress made of colored cotton fabric (sizes 48 - 60). 

The front panel with undercut from the side seam to the neckline and soft pleats instead of Darts. 

From the plastron and podreza the skirt laid unilateral folds. 

Back panel with stretch waist, facing the barrels and accordion pleats. 

Vtachnoy sleeve, three-quarter, slightly narrower. 

Neck Cape. 

The finish of the Cape, the sleeves and the bow made from fabric matching the dress. 


A dress of this style it is recommended that proportionally-built and full women.


Drawing style lines on the pattern (Fig. 127)


Style developed on the pattern of the basic drawing dresses. 


 3аднее panel (Fig. 127). Continue the line of the Darts in the skirt to the bottom, to rasciesa wedges on the side cut from the waist line down to delay 5 - 6 cm, the second line of the tuck - 8 - 10 see the resulting points to connect a smooth line. The length of Pedraza on the side cut from the waist line to make a request, ie depending on the shape it can take 1 - 2 cm above or below. 


 The front panel (Fig. 127, b). From the depth of the neck down to defer 8 - 10 cm and left 2.5 cm Top of neck to connect with point of 2.5. From the end of the shoulder tuck to delay down 3 - 5 cm Side cut shelves from the armhole to the waist to split in half and draw a line podraza connecting point of division points 3 - 5 and 2.5 a smooth line, as shown in Fig. 127 b.


The soft pleats at the shoulder cut of the first line, tuck the right to postpone 3 cm, then the received point and the end of the shoulder tuck to connect with the line of podraza. The pattern to apply a line of rasciesa wedges, which continue the line of Darts in the skirt to the bottom as well as on the rear panel (rascles of the wedges is optional, you can increase it from the side of the slice). Then apply a line of podreza the same as on the back.


For one-sided creases by the undercut on the front panel of the skirt to defer to the left 6 - 7 cm From the points to hold down the line to the bottom, parallel to the middle of the front. 


Pattern pieces are numbered and show the direction of the grain lines. 


Obtaining the modified pattern and cutting (Fig. 128) 

to keep the basic lines of the pattern, along the lines of rasciesa wedges to cut her teeth or the shape of wedges to remove the cutter, having enclosed under a pattern a clean sheet of paper. 

 The rear panel (Fig. 128, a, b). Back to find on the pattern. For one-way pleats to the bib and two side wedges to give allowance for polsladko, ie 7, see 

 the Front panel (Fig. 128, V, g, d). The soft folds in the upper part of the bodice (detail 3) for applying lines to make the cuts, not dorezaya to the shoulder cut of 0.5 cm, and the pattern to push the first and second cut 5 cm (can be cut out without a seam in the middle, put an item to the fold of the fabric) . In the part 4 (Fig. 128, d) from the neck up add 4 - 6 cm for the treatment of valve (upper slicer) or otkroite obtachku on the valve (podkraj piping shown by hachures). 

In a one-sided folds on the front panel of the skirt parts 4, 6, 7 to be expanded to 10 - 12 see 

 note. On the fabric first, you can lay folds, sweep to connect the pattern pieces, lay on a cloth, and then proceed to cutting. 

If the width of the fabric allows you to carve out whole cloth, in the middle of the inner fold of the pleat to make the seam. 

 The sleeve is narrowed down to find the pattern of the basic drawing. 

 Bow to carve out two parts. 

The seam shown in Fig. 128.
 

Tailoring 

1. To celebrate the middle of the back and front panels of the dress cushioning seam. 

2. To lay a snare for the main lines and shaped patterns. 

3. To make nadziejko on the rear panel to the width of the seam allowance for pleats. Tack side of the wedge (item 2) to the rear panel, combining slices of the allowance for polsladko, seam width 0.7 - 1 cm. 

4. Sweep of tackle Darts at the back, then grind down, at the same time grinding off sections of the allowance for folds. 

5. Sew the upper part of the shelves in the middle of the part 3, the seam resaturate, then lay soft folds (the fold of the pleat should be towards the middle of the front).

6. Tack and pritchet flank (item 5) to the plastron front panel, combining snares and folding inside out. 

7. Allowance for this when cutting on upper barrel and cut the plastron to bend towards the inside, put on the top shelf (item 3) by aligning the snare, tack transfer seam, then pricecat from the inside out. 

8. Lay the fold on the front panel of the skirt (the fold of the pleat should be towards the side of the slice). 

9. Baste and sew the side seam of the back and shelves, the seam resuturing.

10. Baste and sew the side seams of the front and rear panels of the skirt, press the seam towards the middle of the front. 

11. Allowance for this when cutting, the undercut shelves and back bend towards the inside, and prometti priotity, the iron to put across, not to stretch the cut. 

12. To put the bodice on the side seams of the skirt, aligning the main lines of the pattern, tack the seam transferable and pritchet from the inside out (see the original Dress is cut with a draped figure podraza). 

13. Baste and sew the shoulder seams shelves and back, seam to press in the back side.

14. Treating the neck and Rostock podkralas the facing. Sew the ends of obcutek shoulder seam to resaturate. Fold the facing with the neck facing to inside, tack and pritchet seam width 0.7 cm, to make the notch in the neckline, the seam resuturing. Fold the facing towards the inside, releasing the roll from the side products by 0.1 - 0.2, see Second section of piping to bend 0.7 - 1 cm, to stitch, then attach hand stitches to the product.

15. Sew sleeve seam, press the seam stitching in the front part of the handle facing the bottom podkralas width 4 5 cm

16. To votate and vacate the sleeve in the armhole. 

17. Hem the bottom of the dress hidden stitches to iron. 

18. For finishing the neck to take a finishing strip of fabric cut on the bias thread equal to the line terminations of Rostock and neck plus 5 - 6cm, width 5 - 6 cm, bend in half, equalizing sections, process them slanted stitches or fold inside out, sew and fold on the front side, press in half and temporarily attach to the neckline.

19. For bow take two strips of finishing cloth length 18 and 14 cm, width 5 - 6 and 4 - 5 cm, to bend along inside out, sew three sides, leaving a sulphur-DIN nezastroennoe, and turn to the front side. 

To impose a smaller bow on a larger, stapled in the center and progenote of the valve, which attaches to a strict Cape.