Dressing gown of plain fabric, collar and pocket flaps are trimmed with fabric in a small cage (dimensions 48 - 64). The bodice poluprilegayuschy, the front panel with scoring barrels at the waist. The robe is double breasted with double-button closure. The back straight telekrona. Vtachnoy sleeve, long, with cuffs and single-button closure. The one-piece stand-up collar-fold-over. 

Gown this style is recommended full and proportionally built women. 

Home gown and robe is good to have an apron draped barrels (Fig. 303, a). 

Drawing style lines on the pattern (Fig. 304)

Style developed on the pattern of the basic drawing dresses. 

 The front panel (Fig. 304, a). The depth of the neck down to delay 4 see Point 4 to connect the top of the neck continuing the line to the width of the cut of the Rostock plus 1 - 1.5 cm i.e. 8 cm From point 8 at a right angle to a line drawn to the right to defer the width of the collar (8 cm) from the bottom of your neck to the right 8 see also Issue unfastened portion of the collar, as shown in Fig. 304.

By the middle of the front cloth to give allowance for polisano, hem 8 - 9 cm, waist 6 - 7cm, depth 3.5 cm neck to Connect the dots, as shown in Fig. 304. 

 The lines of the facing pocket with flap. In the middle of the front from the waist line down to 18 delay cm and the left waist 8 - 10 cm From the point 18 to the left to defer 16 cm (control point to bend the valve). From a point 16 up to draw a line, parallel lines the middle of the front cloth to the waist. Held the line to split in half. From a point 8 - 10 through a point dividing a line equal to 35 cm. From a point 35 down to 15 delay see Point 8 - 10 connect with the dots 16, 15, and continued this line for 2 see Point 2 connected to point 35. The width of the burlap pockets at the waist 3 cm, its length from a point 16 cm - 10 cm

To receive rasciesa skirt to apply a cut line from the point 16 to bottom. 

 Cuff (Fig. 304, b). To build a rectangle with a length of 22 cm (arm circumference plus 4 - 5 cm in length), a width of 6 cm Length 2,5 cm Cape 

pattern pieces are numbered and show the direction of the grain lines and control points.
 

Obtaining the modified pattern and cutting (Fig. 305) 

For applying the pattern lines to cut. 

 3аднее cloth to cut out the pattern from a basic dress with no modifications, the middle of the pattern to put the fold of the fabric at common thread. 

 The front panel (Fig. 305, a). The front cloth patterns translate the cutter shape a side of the skirt (Fig. 305, b) and cut it out, the resulting pattern put on fabric and cut out along with the burlap pocket on the bottom for rocklee to give an allowance of 6 cm.

The front panel to carve out together with pocket flap, placing the pattern so that the middle of the front was the common thread of the fabric. For rascles on the bottom add 6 cm to Make podkraj to handle valve along with the burlap pocket. 

 Top collar to carve out together with the Board. The length of podbot you can natacat in several places. 

 Cuff to carve out a double (two part).

The seam and stocks is shown in Fig. 305. 

Tailoring 

1. To celebrate the middle of the front and rear panels of the robe slip stitch. 

2. To lay a snare for the main lines and shaped patterns.

3. Processing obecnie loop on the flap and sides. 

4. Baste and sew the Darts on the bodice.

5. Treating a curved flap pockets podkralas the facing, cut along with the sacking of the pocket of fabric finishing. Fold the facing and the valve face inside, to equalize the cut and sew from three sides, from the waist line and to the checkpoint. To turn on the front side, straightening the seam, ironed, against the loop to make a cut on the flap and sew the seam of the loop of concealed stitches. Put the front panel of the skirt on the side, combining the snare and sew burlap pockets and front panel with the message from the control point to the bottom line.From control point of the weld width should be 0.2 - 0.3, see the pocket Flap from the control point to bend so that the lower Cape was located upwards, and fasten with a button. The lower part of the valve to attach to the product of concealed stitches so that it was below the line of the pocket.

6. The rest of the treatment of the robe is the same as in the fitting 86. 

Drawing style lines on apron pattern (Fig. 306) 

the Style developed by the pattern of the basic drawing dresses. 

 The front of the apron. From the top of the neck at the shoulder cut to the left to defer 3 cm, and the depth of the neck down - 10 - 15, see Point 3, 10 to 15 to join. From the neck to the right armhole at the shoulder slice to postpone 2 see Point 2 are connected with the end of the shoulder tuck a smooth line, extending it to the end of the pulley-block Darts. From the waist line on the side cut up to be postponed 4 to 5 cm and from point 2 at the shoulder side down - 6 - 7 see Point 6 - 7, 4 - 5 to connect a smooth line, extending to the left 5 - 10 cm (desired length of apron).From the line down the middle of the front cloth to defer up to 4 - 5 cm, side cut - 20 - 25 see Point 4 - 5, 20 - 25 to connect a straight line, continuing it over the side of the cut at 11 - 15, see Point 11 and 15 to be connected to point 5 - 10.

 Line the entrance to the pocket. From the waistline at the side cut down to lay 10 - 12 cm and hold a smooth line from the first line of tackle Darts through a point 10 to 12 to the intersection with the line entering the apron. 

To obtain the draping on the sides of the apron to cause the section line, dividing line traveling tuck into three parts. From the points of division draw lines to the intersection with the side cut, as shown in Fig. 306.
 

Obtaining the modified pattern and the cutting of the apron (Fig. 307) 

For applying the pattern lines to cut. 

 The front part (Fig. 307, a). The middle of the pattern is put to the bend of the fabric. For entry straps on the back to keep them to length measurements length backless to waist plus 5 - 6 cm or otkroite straps separately. To handle sections of the apron to otkroite obtachku on the bias yarns of the fabric finishing with a width of 3 to 4 cm, and for treatment of the neck - by a transverse filament. 

 The flank (Fig. 307, b). To obtain assemblies for applying the pattern lines to cut and separated by 3 cm (optional). To find the two parts together with a burlap pocket with a length of 20 cm, width 15 - 18 cm For processing the upper edge of the pocket to otkroite burlap in the form of a line of entrance to the pocket length and width of the lower part (Fig. 307, b). 

 Belt. From barrel to carve out two parts of length equal to the circumference of the waist plus seam allowance on the bow 20 - 25 cm. Width of the belt as desired. 

The seam and stocks is shown in Fig. 307. 

Sewing apron 

1. Mark the middle front and waist seam cushioning.

2. To collect Assembly on the side parts of the apron. 

3. Sew straps of shelves with a back. 

4. To treat the neck podkralas a facing of fabric finishing.

5. Tack on the entrance line into the pocket of burlap, folded it with the wrong side inside, equating sections. Then the front parts 1 at the cut edge of the barrel tack finishing bake, folding her face with the apron wrong side, tack and pritchet simultaneously with the burlap pocket. Bake bend on the front side, releasing the roll from the bakey 0.1 - 0.2 cm, and promette. The second cut bend inward at 0.5 - 0.7 cm and tack. At the entrance line to the pocket pritchet bake at 0.1 - 0.2 cm from the bend. To put the front of the apron on the flank, to baste, combining snare, and sew the burlap.Then Topstitch the apron on the flank for the Baker, stepping back from bend it by 0.1 - 0.2 cm to the entrance to the pocket, clipping cross stitching.

6. Tack the straps to the barrel, arms folded, right sides inside. 

7. To handle the side and bottom of the apron edging and at the same time vracheva ties. 

8. To prometti the loops on the straps of the back. 

9. Sew buttons on straps.