Dress of silk or cotton fabric in plain or fine pattern (sizes 46 - 52), casual, notched yoke with zipper on three buttons. Under the yoke of the bodice're. The scoop neckline. Sleeve short one-piece. A wide band of fabric finishing. 

A dress of this style can be recommended slim and proportionally built women. 

Drawing style lines on the pattern (Fig. 247) 

the Style developed by the pattern drawing tselnokrajnimi bodice with short sleeve. 

 The rear panel (Fig. 247, a). To deepen and expand the neck of the sprout to 3 to 4 cm openings to connect with the side cut. 

 The front panel (Fig. 247, b). To deepen and expand the neck for about 3 to 4 cm From the second line of the tucks at the shoulder cut to the left to defer 6 see the first and second lines of the shoulder tuck down the delay to 11 cm, and the depth of the neck is also down 20 cm From the point 20 to the left to defer 4 cm and from point 4 upwards, parallel to the middle of the shelf is 10 cm to Make a decorative yoke of the connecting point 6 with points 11, 10 a smooth line.

From the neck to the middle of the front yoke to give allowance for the setting of the fastener 3 see For getting the assemblies to apply a cut line connecting the ends of the shoulder and tucks tackle, then from the end of the pulley-block Darts on the skirt to hold the line to the bottom parallel to the center of the front panel. 

Pattern pieces are numbered and show the direction of the grain lines. 

Obtaining the modified pattern and cutting (Fig. 248) 

 Back panel (Fig. 248, a) be cut out of the pattern without changes. To otkroite piping for processing armholes and Rostock. 

 The front panel (Fig. 248, b). For applying the pattern lines to cut, close the shoulder dart into the yoke. To increase Assembly cut the pattern from the end of the shoulder tuck, not dorezaya to the hem is 0.5 cm, and take her to the left 3 to 4 cm 

For coquette (Fig. 248, in) to carve out four details the common thread. 

The seam and stocks is shown in Fig. 248.
 

Tailoring 

1. To celebrate the middle of the back and front panels of the dress, yoke, and slip stitch. 

2. To lay a snare for the main lines and shaped patterns. 

3. Gather front of bodice to the Assembly, spreading it evenly. 

4. Handle hinges on right side of yoke.

5. Fold the lower yoke and the upper face inward, equating sections, and sew the neckline and the edge of the clasp. Seams to resaturate remove the yoke on the front side. To put the right yoke on the line entering on the left. The lower portion of the right yoke on the level of entry of the left yoke to nadsech seam width and the notch grind from the bottom of the left yoke.

6. To process the corners of the yoke: the inner corners have rounded part of the handle yoke to the facing (Fig. 248, g, d), and the lower end of the upper yoke to handle the allowance given when cutting. The seam allowance folded away towards the inside, the fabric in the corner to sweep, and sew the excess fabric to cut, the seam to spread, to turn the corner on the front side. Then the upper sections of the yoke to bend inside out, sweep and priotity. 

7. To baste the top yoke on the front panel of the dress, combining snare, and Topstitch it wide of the finishing line (1 - 1.5 cm). 

8. Handle Rostock podkralas the facing.

9. Baste and sew the shoulder seams of the back and shelves, at the same time grinding off the ends of piping Rostock and the lower yoke. 

10. Baste and sew the side seams, stitch resuturing or to press towards the front cloth of the dress. 

11. Processing podkralas the armhole facing. 

12. Hem the bottom of the dress, to iron and to sew. 

13. To handle the belt.