Sleeveless wool plain fabric (sizes 48 - 60), single cut, with a deep neckline. 


In the middle of the front cloth skirts one-way pleat. 


Front button placket and Welt pockets. 


The back of the three wedges. 


This sundress can be worn with a belt. 


Drawing style lines on the pattern (Fig. 233) 


the Style developed by the pattern of the basic drawing dresses. 


 3аднее flag (Fig. 233, a). The width of the sprout at the shoulder slice to increase by 4.5 cm In the middle of the back sprout to deepen for 10 - 15 see plotting points to connect a smooth line. The line of openings to divide in half and make a cut line from mid-armhole to the end of tackle Darts in the back. Line tuck to continue to the bottom. On the side to deepen the armhole cut 4 cm and point 4 to connect with the breaking point smooth line. 


For rascles hem to the side cut add 5, see 


 the Front panel (Fig. 233, b). From waist line down the middle of the front to defer 18 cm and hold the line of the hips. The width of the neck at the shoulder slice to increase by 4.5 cm and from the depth of the neck down to defer 20 see Points 4,5, 20 connect. Held the line to split in half and left to defer 1.5 cm to Make the neck smooth line.


The line of the armhole split in half and the point of division to connect with the end of the pulley-block Darts. The end of the shoulder tuck to connect with sideways. On the side to deepen the armhole cut 4 cm and point 4 to connect with the breaking point of the armhole a smooth line. From the waist line on the side cut down to be postponed 4 to 5 cm From the middle of the front panels on the hips to the left to defer 18 cm, and from a point 18 up - 2 see Point 4 - 5 to connect with the point 2, then point 2 - with the second line tuck. Held the line to split in half and the dividing point to the right to defer 1.5 cm Draw a line of entry into the pocket, as shown in Fig. 233 b.For registration of the burlap from end of the traveling tuck to hold the auxiliary line on 4 - 6 cm below the hip line. The width of the burlap at the waist line equal to the depth of tuck. To make burlap, combining the first line of the depth of the tuck and point 4 - 6, 2 a smooth line. To give allowance for the length of the clasp from the depth of the neckline and the hip line by 2.5 cm.


For rascles hem to the side cut to add 7 see 


pattern pieces are numbered and show the direction of the grain lines, to supply the control points. 


Obtaining the modified pattern and cutting (Fig. 234) 

For applying the pattern lines to cut. 

 The rear panel (Fig. 234, a). In order not to disrupt the contour lines of the pattern, remove the pattern of the wedges with a chisel or cut teeth. The middle of the pattern medium wedge (Fig. 234, a) to put to the bend of the fabric. The pattern side of the wedge (Fig. 234, b) put on the fabric so that the middle of it was the common thread. 

 The front panel (Fig. 234,). In the lines to make undercut by the end of the shoulder tuck, close it, and this will open a new dart at the line barrel. By the middle of the front cloth to allow for a unilateral fold of 6 cm 

 Side (Fig. 234, d) carve out together with the burlap pocket common thread. 

To find the second piece of burlap (from the main fabric), which is both a facing for the processing of the cut of the pocket (Fig. 234, d). 

The seam and stocks is shown in Fig. 234.
 

Tailoring 

1. To note waistline, mid-back wedge, front cloth of the dress and the waistline seam cushioning. 

2. To lay a snare for the main lines and shaped patterns. 

3. Sweep medium wedge cloth back side, aligning the waist and control points. 

4. Lay a soft pleat to the cutting line of the barrel and at the waist on the front panel. Tack flank to the front panel of the dress, combining the traps and checkpoints. 

5. Sweep the crease on the front panel of the dress. 

6. Baste shoulder seams, propositiva back.

7. Sweep the side sections from the armhole to the bottom, aligning the waist and control points. To do a first fitting. 

8. On fitting to clarify the position of the pockets, their distance from the middle of the shelves, the position of the hinges, the design of the neckline, the arm openings. 

9. After the fitting process obecnie loop (see here). Stock on the crease at the end of the zipper to cut across to the middle of the front cloth, then make a cut along the line of the allowance for entry of fasteners left shelves, fold the seam allowance on the front side and at the end of the clasp to perestroit it across. The left shelf to handle equity facing a width of 5 cm, the facing should extend beyond the middle of the shelves on 2 - 2,5 cm

10. Fold the burlap with cut pockets inside out. Tack and pritchet, slightly propositiva fabric at the entrance line to the pocket. In the corner to make nadziejko, burlap bend on the wrong side, straighten and prometti seam from the fold, releasing the roll from the primary by 0.1 - 0.2 cm due to the tuck to lay a soft fold at the pocket and to fix her cross-stitching. 

11. Tack and pritchet flank to the front panel, simultaneously grinding off the burlap pocket and continuing the line up to the side of the slice.

12. Handle cutout Rostock and neck podkralas the facing. The ends of obcutek neck pre-sew slices fasteners, seams to resaturate. 

13. Sew shoulder seams, simultaneously grinding off the ends of obcutek Rostock and neck. 

14. Sew the side seams. 

15. Processing podkralas the armhole facing.

16. Hem hem, iron and sew on buttons. Buttons can be made of fabric product. To do this on the bias thread to find angles length 13 - 15 cm, a width of 5 - 6 cm (Fig. 234, e). Edging the edges bend so that they were connected in the middle. The wide side of the bend corner (Fig. 234, W), then turn in the form of a tube having bends uniformly (Fig. 234, z). At the end of the edge of the area to bend and hem with thread to match the fabric. To the button loop is not recommended.