In terms of making clothes for individual orders you have the cutter operatively in the shortest terms to carry out the decision of different models of products, including vests. It is necessary to use a structurally-based silhouette. Here are some examples of vests on the same constructive basis.
 

 MODEL 1 (Fig. 30). Backrest and shelf vest with a detachable belt. The joint yoke of the shelf valve with a loop. On-line front tuck relief to the line of yoke at underarm. Through the back tuck is moved to the left. Through the tuck is a relief. Back waist extended for tightening rubber band. The deflection of the tank increased slightly. Line polutanata at the top, at a right angle to the neck. Closure by five buttons.The distance between the upper first and second from the top loop and the bottom of the first and second from the bottom of the same, between the hinges of the second, third,and fourth distance are also the same.
 

 MODEL 2 (Fig. 31). Backrest and shelf vest with a detachable belt at the top. On the shelf invoice nastroni decorative pocket, through which passes a strap. Strap from the chest line to bottom aligned with the line А4Т4; from the chest she goes up to the middle line of the yoke. Strap attached to the pocket lace, threaded through holes in a metal festoons.

On the back strap of the yoke is a continuation of the strap on the shelf. Under the strap at waist level-tab is fixed in the Darts on the back. Strap nastraivatsa two decorative lines. Solution front tuck transferred to the side seams. The width of polosamota in the top 6.5 cm, bottom 5.5 cm.
 

 MODEL 3 (Fig. 32). In the drawing, make changes to the design depth and length of the tank. The tank bottom lug ends with two loops. At the level of the ledge and in accordance with its width stachivaya in front tuck the belt loops with a buckle. The belt loops two buttons.

Armhole on the shelf has a rectangular cutout. To build up from point lay G4 1.5 cm and through the obtained point and the point G5 to the right hold a line that intersects a line perpendicular to this line from point P5 to point G4'. The line of the armhole on the shelf is carried out through П5Г4, G5. On the shelf of a narrow leaf.

 MODEL 4 (Fig. 33). The vest is lengthened, the shelf has at the bottom of the fillet. The tank is deep. Armhole expanded and deepened. Side pockets with shaped flaps. The solution is transferred tuck in the side seams.
 

 MODEL 5 (Fig. 34). Back relief from the level of the shoulder blades from armhole to the hem (point N11). Shelf with notched lapel and relief from the armhole to the point on the line Т4А41 (between the lines of the chest and the waist) up to the side of the slice. In the lower part of the relief pocket with leaflets. The clasp on the buttons.

 MODEL 6 (Fig. 35). The back and shelf with a notched belt. From under the Cape yoke on the shelf a curved flap. The vest on the back shortened. The bottom has an oval line from point N11 on the back to the side seams. A bevel on the bottom shelf from the point L1 to the point Н53 located at the intersection of lines А41Т4 and Н51Н21. Tuck on the back move to the left and build on the vertical from the Cape of yoke to the bottom. Solution Darts at the back and the side seam increases due to the straightening of the midline of the back from point Y1' vertically to the bottom line (dot H13).
 

 MODEL 7 (Fig. 36). Backrest and shelf with yoke and reliefs from the yoke to the bottom. Darts at the back moved to the reliefs. Upper pockets with flaps, lower Welt flap. Shoulder seams, tapered slightly exaggerated. The bottom shelf has a pointed form with a top angle at the point Н53.

To build the collar from point L, hold tangent to the neck at the point F2. At the intersection of the tangent with the line of the shoulder put a point S0. On the continuation of the direct Лз0 upward from a point S0 delay period equal to the length of the neck of the backrest (without the seam allowance at the shoulder cut), and put a point P1. From the point F2 of radius equal to the segment Ф2з1, conduct an arc to the left. From the point Z1 to the left along the arc lay cut з1з2 equal to the width of the flight, i.e. з1з2 = 4 see the Points of Z2 and F2 connect with a straight line.At the point Z2 raise a perpendicular to a straight з2Ф2 and from the point of Z2 delay period, equal to the sum of stand height and width of departure з2з5 = 1,7 + 4 = 5.7 cm From the point of Z2 down in a straight line з2Ф2 lay 0.5 cm on the sling collar (point з21). Point з21 and H5 connect with a straight line. From the point з21 direct з21з5 lay stand height з21з4 = 1.7 cm

Cut, equal to the width of the collar at the ends of the lay from the point to the A61 and put a point P6. The width of the collar at the ends and form a collar should match the chosen model. Line vrachevanie collar make it sags in the middle, equal to 0.3 see the Point H5 and P6 connect direct. From the point H5 in a straight з5зб lay 4 cm (point з51). External cut of the collar make it sags in the middle straight з51з6 equal to 0.5, see the Line stands is carried out from the point з4 parallel to the line of vrachevanie collar з21Ф2 with a smooth transition from the line 'stand collar to the fold line of the lapel.