BATHROBE FOR GIRLS

Size 36
Measurements:
the total length of the Bathrobe........ 75 cm
back length to waist...... 33 cm
shoulder length . . . . .. . . .. . 12 cm
neck circumference............. . 16,5 cm
the circumference of the chest.......... . 36 cm
sleeve length.................. 45 cm
sleeve length to elbow.... 28 cm
the circumference of the armhole......... 33 cm

Build back. Fig. 50

Take the plan line AB is equal to 14.5 cm from the calculation of 1/5 of the circumference of the chest: the chest circumference 72 : 5 = 14.4 V (about 14.5 cm).
From points And drop a vertical line equal to the length of the product is 75 cm and Then from point A fall to 18 cm from the calculation of 1/4 the circumference of the chest: the chest circumference 72 : 4 = 18 cm.
From the point 18 to the right draw a horizontal line of chest 18 cm from the calculation of 1/4 the circumference of the chest: the chest circumference 72 : 4 = 18 cm.
From the right 18 point drop a vertical line and connect it with the point 75. The resulting angle is denoted by the point D.
From point A down to 1 cm (standard), then from point A to the right of the line plan delayed 5.5 cm is based 1/6 neck circumference: neck circumference 33: 6=5.5 cm.
Point of 5.5 connecting by hand a concave line with point 1 and get the neck back.
From point B down to 3.5 cm (bevel shoulder backless). From the point 5,5 hold a straight line through the point of 3.5, and lay off on this line the length of shoulder - 13 cm (length of shoulder of the back 12 cm, plus 1 cm on the landing).
From the point of 3.5 on the Breasts drop dashed vertical line and divide it in half. The resulting angle denotes the point On the dotted lines, which divide the angle in half G measured 1.5 cm From the hand of the concave line connecting point 13 point division, point 1.5 point 18 and get the armhole of the back.
From point 1 down to 33 cm (length to waist) and from the point 33 to the right are waist line and denotes the point T. From the point T to the right postpone 1 cm and Then by a straight line connecting point 18 (armhole), with point 1, continue straight to the bottom of the product and is connected to the point 75. From the resulting oblique angle rise for 1 see Point 1 of the free line, no connect with the middle of the bottom of the product.

Build shelves. Fig. 51

Take the plan line AB, equal to 15.5 cm, at the rate of 1/5 of the circumference of the chest plus 1 cm the chest circumference 72: 5+ 1 = 15.5 cm.
From points And drop a vertical line 78 cm based on the length of the product on the back plus 3 cm: length at the back 75+3=78 cm
From point A to the left of the line plan and down-delayed at 6.5 cm from the calculation of 1/8 the circumference of the neck plus 1 cm: neck circumference 33: 6+1=6.5 cm.
Connecting with the concave line of 6.5 points and 6.5 and get the neck shelves.
From point A fall to 18 cm from the calculation of 1/4 the circumference of the chest: the chest circumference 72:4=18 cm
From the point 18 to the left draw a horizontal line chest 23 cm from the calculation of 1/4 the circumference of the chest plus 5 cm: chest circumference 72: 4+5=23, see
From point B down to 3 cm (bevel shoulder forehand). From the point of 6.5 through the point 3 hold a straight line and lay off on it the length of the shoulder shelves 12 see Then from point 3 we omit the dotted line on the line of the chest, and denoted by the point G. the Line of dashes divide in half, and from the dividing point to the right delay of 1 cm Line from point G to point 23 divide in half, and from the points of division are omitted for 1.5 cm then drawn armhole shelves robe: of the arms are concave line from point 12 through point 1, point G, point 1.5 K point 23.
Then measure the length of sides of the back from point 18 to point and from point 23 drop a vertical line equal to this length. The point denoted by the point T. From the point T to the right the dotted line to the intersection with the line A78 and put the point T1. From point T1 falls to 3 cm, point 3 a smooth line from the hands connected with the point T and get the waist line shelves.
From the point T to the left delay 3 see Then from the point 23 through the point 3 hold a straight line lay off on it the length of the side shelves are equal to the length of the sides of the backrest (from point 18 to point 1, in the drawing marked with three dashes) and put the point D.
In order to draw the side of the gown, from the points of 6.5 and 78-delayed right at 4 cm From point 4 (top) up to 1.5 cm and from point 1,5 hold a straight line to point 4 on the bottom line. Point 1,5 concave line from the hands connected with the point of 6.5.

The construction of the sleeve. Fig. 52

Take line 33 cm calculate the circumference of the openings and build the rectangle ABC size 33 cm to 45 cm, where 45 cm - sleeve length.
From point A down to 11 cm from the calculation of 1/3 of the circumference of the armhole: the armhole circumference 33: 3=11 cm.
From point 11 to the right draw a horizontal line to the line BG and denoted by the point O. the Line AB divide the plan into six equal parts and the points of division denoted by A1, A2, A3, A4, A5, from each point of division a vertical drop line to line 11P.
The intersection of the vertical line from the point A4 with a line of 11 POINTS denoted by the point P1 from the point A5 point P2.
From a point And go down 7 cm from point A1 - 2 see Point A2 - highest point of the sleeve. From point AZ fall to 2.5 cm, the distance between point P1 and P2 divide in half, the dividing point falls at 0.5 cm From point B down to 7 cm from Left to right from point 7 through point 2 to point A2 through the point 2,5, point P1, point 0,5 point P2 and the point 7 of the concave line hand-drawn head of the sleeve.
From points A and B fall to 28 cm (sleeve length to the elbow), connect points and get a line the elbow, From the point To the right and from the point G lay off to the left 3 cm From point A3 drop a vertical line to the line VG and climb up on it on 2 see Point 3 connect straight lines from point 2. Then point 3, respectively connected by straight lines with the point 28.

The construction of the collar. Fig. 53

Build the rectangle ABC with a size of 16.5 cm by 9 cm is based 1/2 neck circumference: neck circumference 33: 2=16,5 cm 9 cm - width of collar (optional).
From point B down to 2 cm from the point A to the right of the line plan delayed 5.5 cm is based 1/6 neck circumference: neck circumference 33: 6 = 5.5 cm.
Point 2 connected by a straight line with point of 5.5. From b rises by 1 cm From the point G lay off to the right 3 see Point 3 connect straight lines from point 2 and point 1.
Mid collar - line A1 has a fold of material and cut out the common thread.

Cutting and tailoring

The middle of the back has a fold of material and cut out the common thread (if the material is narrow, and the seam).
The middle of the front cut out as the common thread. Podborny robe otkrivaetsa on a tailored coat (pattern a - line dotted) . Podportila width of the shoulder should be at least 4 cm, at the bottom - not less than 3 cm.
The collar is sewn padbottom by the rules.
Cuff cut out the common thread in half. On the sleeve under the cuff, an incision is made and processed by plate No. 2 (Fig. 157).
Bathrobe coverstitch sewn or lapped seam. The hem of the robe is stitched with its material, the width of bending 1 cm.
Last sewn pockets, which can be pristroit on the machine or sew by hand so that the front side was not visible lines. Pockets can be cut in various forms and development.

THE SKIRT FLARED BELL. Fig. 54

Measurements:
the length of the skirt ................. 65 cm
waist circumference......... 34 cm
Take the plan line AB, equal to 86 cm, calculate 1/4 waist circumference plus 4 cm and plus 65 cm skirt length: waist circumference 68: 4+4+ 65= 86 cm
From points And drop a vertical line equal to line plan and put the point V. From point A to the right of the line plan and down-delayed for 21 cm calculate 1/4 waist circumference plus 4 cm: waist circumference 68: 4+ 4 = 21 see
The angle And divide in half, draw the line of the dotted line, equal to line plan and put the point 86.
From point A on the dotted line-delayed 21 cm (1/4 waist circumference plus 4 cm). Point 21 connected by hand a concave line and get a waistline. Flared skirts are plotted, in a semi-circle connecting the point B with the point 86 and a point In (for smooth bottoms needed from the waist to put the support point, the direction of which is shown in dotted lines. Skirt length from waist to any point on the bottom of the same.

Cutting and tailoring

Line of AB - share and in the layout pattern in the material stack only equity, the line AB is transverse and when you cut is placed only at the cross. To cut this skirt should be in one sheet in two patterns, putting them on the front side. To lay out the pattern on the material strictly according to the direction of the thread (Fig. 55).
If the material is narrow, then pretrazivati wedges only common thread (one wedge - front, second rear).
The side skirts fold cross equity and smatyvay the transverse thread. The hem is stitched with a hem no wider than 3 cm according to the rules of bending the skirts flared.
The skirt seams at the sides, prorezka on the left side at the seam line (you can sew a zipper or make hidden). The skirt is the bell doing on the belt or on the waistband (see treatment of the corsage).
Flared skirt with a single seam can be tailored pattern skirts the semi-circular (Fig. 54). When you cut the skirt material folded in half and the pattern is placed on the fold of the material so the side patterns "at equity" lay on fold of material; a transverse direction as it will fall on the material (Fig. 56). Optionally, you can do with a seam the middle of the front or rear of the canvas.

SKIRT SELECLINE

Measurements:
the length of the skirt.................. 65 cm
the circumference of their hips......... 44 cm
waist circumference.......... 34 cm
Take line plan 15.3 cm(16 cm) thigh circumference plus 4 cm on free fit for all sizes divided by 6: the circumference of their hips 88+4=92; 92: 6 - 15,3 see
Build a rectangle the size of 15.3 cm by 65 cm, 65 cm - length skirts.
From the line the plan falls to 18 cm and draw a horizontal line of the hips is based 1/2 length back to waist: back length to waist-36: 2 = 18 cm
Lines plan and bottom, divide in half, point dividing the join of the straight dotted line. On either side of the point dividing the line plan delayed by 5.7 cm of calculate 1/6 of the circumference of the waist divided in half: waist circumference 68 : 6 : 2 = 5.7 cm 
Point of 5.7 hold straight lines through the points 18 and over 65 cm (length skirt). The point of recklessne connected hand-free lines to the lower corners of the rectangle and obtain the pattern of the wedge skirts seliclinked. You need to recklessne in both directions was the same.

Cutting and tailoring

The middle wedge - dotted line - "equity". When you cut the skirt seliclinked it is necessary to use two or three patterns, depending on the width of the material. Pattern laid on the material so that the middle wedge was the common thread, one wedge went waistline, another bottom line (Fig. 58).
This layout needs to consider the direction of the pattern of the material; if the material is one way to sew clinovia skirts unprofitable and not recommended.
If a cut is made in three patterns (wedges), the canvas is folded in half, and if two, then three.
All drawings skirts-blade regardless of the odd or even number of wedges (e.g., 5-blade, 8-blade, etc.) are built on this principle. The waist measurement is divided by the number of required wedges.
To the seams to add rules.
Wedges are sewn together coverstitch seam and smoothed on two sides, light materials, you can sew a reverse stitch.