Thursday, 28.03.2024, 14:35
Welcome Guest | Sign Up | Log In

All about sewing

Site menu


Section categories
Sew yourself
The ABCs of sewing
Women's clothing
Sewing for little
Designing men's outerwear
Cutting tailoring modeling women's lightweight clothing
Cutting and sewing of women clothes
Technology women's and children's light clothing
Technology of sewing production
Women's and children's dress
A hundred styles of women's dresses
Fashion tops
The basics of the art of designing clothes
Design basics clothing
Modeling and design artwork for women's and children's clothing
The manufacture of men's and children's costumes
Manufacturer of women's and children's outerwear
Art beautiful dress
According to the laws of beauty
The art of sewing
Design women's coat
Design basics outerwear
National clothes
Search
Log In
Site friends
Statistics

Total online: 1
Guests: 1
Users: 0

Home » Articles » Sew yourself

Dress with large collar

Dress of thin silk or cotton fabrics, colored or monochromatic (Fig. 16). Recommended sizes - 44, 46, 48, 50, cut at the waist with an open neck oval shape on the front and Cape at back, sleeveless. The skirt is wide ("bell") 8 - or 12 - blade. Big collar, front rounded at the back with sharp ends. 

To the treated the neck primatyvajutsja different collars of dress fabric or finishing, in this case, the dress will always look fresh, updated and elegant.

The number of wedges you can increase or decrease depending on the completeness of the figure. Slim women should wear trousers or crisp skirts. 

Drawing style lines on the pattern 

Style developed on the pattern drawing attached bodice (Fig. 17). 

 Back. Widen the neckline of Rostock at the shoulder cut into 5 cm (optional) depth of the cut in the middle of the back will increase to 14 - 16 cm (optional), points 5 and 14 (16) connect and place the neck of Rostock. Reduce the cutout openings 2 - 3 cm For the side cut from the bottom of your armhole up will continue for 2 - 3 cm and draw armhole.
 


 Collar to the back. The length of the collar at the shoulder cut of the back 10 - 12 cm In the middle of the back from point 14 - 16 put down 5 cm from the point to the right 5 see Point 14 - 16 and 5, connect, continuing the line so that it was equal to the length of the collar at the shoulder cut, that is 10 to 12 cm For the rounded ends of the collar width from the shoulder cut to negate the depth of the cut sprout in the middle of the back.

 Shelf. The width of the neck at the shoulder cut is equal to 5 cm depth of neckline in the middle of the shelf put down 6 - 8 cm Fill neck, connecting points 5 and 6 - 8. Slim cut-out openings for 2 - 3 cm similarly to the armhole of the back. 

The length of the collar at the shoulder cut is equal to the length of the collar backless (10 - 12 cm). From the depth of the neck at the mid front, i.e. from point 6 - 8 down-set aside 10 - 12 cm and left 3 cm (below the collar lifted from the neck). Connect the dots 3 and 6 - 8 and complete the bottom line of the collar, parallel to top.

Below the collar on the neck lay without the influx, exactly, no need to cut 3 cm at the middle of the front. 

When cutting the middle of the patterns put back to the fold of the fabric. The seam on the neck - 0.5 cm, armhole - 1 cm, at the shoulder seam and 1.5 - 2 cm, lateral - 2 - 3 cm and at the bottom of the backrest for the stock and the seam is 4 - 5 cm. 

The middle of the pattern when cutting is put to the bend of the fabric. The seam is the same as on the back. 

For cutting of the collar fabric fold in half inside out and pattern the middle of the front of the collar to the fold of the fabric so that it was the common thread. 

 Skirt. For cutting wedges skirts remove the following measurements: the skirt length (DU) - 75 cm; full scoop waist circumference (FROM) - 72 cm; hip (ABOUT) - 112 see 

Complete measurements of waist circumference divide by the number of wedges. Solution of the wedge along the lines of the hips is defined by dividing the hip measurement by the number of wedges. If the skirt at the waist slightly gathered, the width of the wedge at the waist and the thighs is increased by 2 - 3 cm.

Fabric consumption depends on its width, the width of the fabric must be already 90 cm skirt requires two panels, the length of each of them is equal to the length of the skirt plus the radius of the recess of the wedge. To find the radius of the recess of the wedge at the waist line for the skirt flared ("bell"), we need the complete measurements of waist circumference divided by 3 (3 is a constant for all sizes) and add the resulting figure to the circumference of the waist. For example, waist circumference 72 cm:
 

72 : 3 = 24; 
72 + 24 = 96 cm


Fold the fabric in half face inside. Compatible sativum edge and 1 cm from the edge. The width of the fabric on the top cut divide in half, from the points obtained draw the line parallel to the edges on the bottom of the tissue section, then the dividing point of the upper edge of the connect on the ruler to the opposite corners of the slices.
 


In this cutting (Fig. 18) from a single sheet of tissue 4 is cut in the shape of a wedge 2 wedge in the unfolded state (D. I), 2 wedge is collapsed (D. II and III), which grind in the middle (on the edges). 

From inexpensive fabric to slim the figure, you can find not 8, and 12 wedges, it should take three lengths of skirt.



Category: Sew yourself | Added by: 12.10.2017
Views: 347 | Rating: 0.0/0

Total comments: 0
avatar