In order that the sleeve looked good on the elbow and was comfortable to wear, you should front seam of sleeve before smachivanie to delay, at the elbow seam to make a landing or a tuck. Scribble stitching on front cutoff sleeves, ironed or zavturove it towards the front. 

Bottom of sleeves processed bent or podkralas a facing, elastic, cuff, cuffs. Advanced, oblique, lesavoy sleeve hem can be treated with a zigzag stitch.

Pokraina the facing is applied to a long, seven-eighths, trehchetvertki, short, sew-in and cap sleeves. After fitting of along the string, place the bottom of the sleeves. Cut the facing of the main fabric in the shape of the bottom of the sleeves in an equity or cross thread.

A long, narrow sleeve width obtachki 4 - 5 cm, wide: 7 - 8 cm Length of piping equal to the width of the bottom of the sleeves with a seam. Prostrachivajut the facing, the seam razotajiem, the lower section of piping bends towards the inside on 0.7 cm, scribble from the bend of 0.2 cm and ironed. Tack the facing to the cut sleeve inside out, scribble stitch width of 0,5 - 0,7 cm Seam stitching will rasutim, tognum the facing towards the inside of the sleeve, straighten the seam, releasing the roll from the sleeve by 0.1 - 0.2 cm, numitem, protogem and filed concealed stitches.For products made of cotton fabrics of the second section of piping bends towards the inside, tack the sleeve manually or scribbling on the car.

Banded cuffs cut double the width and shape of their depend on the style. Sew in the following way. Fold the top and bottom side to the cuff inside out, equating slices, grind unfastened portion of the cuff, the seam will rasutim, turn the cuff on the front side, straighten the seam, releasing the chute from the upper cuff by 0.1 - 0.2 cm, amatem and let's iron it.

Advanced down a sleeve assembled on an Assembly equal to the width of the cuff, or put small pleats on the front of the sleeve in the direction of the elbow joint. The lower part of the cuff applied to the front side of the sleeve, equating slices the cuffs and sleeves, tack, grind, seam width 0.7 cm 

The bottom of the sleeve will pomognem allowance to the top and sew the cuff to the sleeve blind stitch hidden stitches. 

 Handle the bottom of the sleeve cuffs. When cutting to the desired length of the sleeve make the stock 6 - 7 cm Flaps to cut out of basic or finishing of fabric with a width of 10 - 12 cm, length equal to the width of the bottom of the sleeves with the seam allowance on the seams. The cuffs cut in a single equity, transverse and oblique directions of the thread. Grind, razotajiem seams, tack the front side of the lapel to the front side of the bottom of the sleeves, the joining seam piecing together the sleeve with the seam of the lapel. Pristrochite will do a roll to the side of the sleeve by 0.1 - 0.2 cm, numitem, Ataturk. The second cut of the lapel processed by machine or by hand. The lapel will tognum to the desired width and Ataturk.

 Matiwane sleeves in armhole. The sleeve in the armhole, you can ultivate in two ways. 

 1st method. Fold the bodice wrong side inside, combining shoulder, side seams and the seam of the armhole. Will Skolem pins or PrimeTel, stepping back 2-3 cm from the slices of openings. Note the snare guide line ultimania sleeves and checkpoint caused during the first fitting. Attach the right sleeve, the left wrong side inside; move the control point from the right sleeve to the left. Connect the sleeve to the armhole with pins on control points. Votives on the sleeve between the two padded thread with small stitches, starting from the reference point to the right and moving his fit. Joint width 1 - 1,5 cmSleeve in a vertical position in the figure should look smooth, without creases. Before setting protogem will fit in the sleeve on the block, then whichim sleeve seam and let's iron it, then tognum the seam toward the sleeve and let's iron it again. The seam of the sleeve and armhole processed overlock seam in loose fabrics - edged, slim - fitting cuts inside. Seam sleeve and side seam of the bodice does not have to match. Basically, the suture sleeve is moved to the shelves on 2 - 3 cm.

 The 2nd method. Fold armhole in half, starting from the shoulder seam, even the seam of the armhole backrest and shelves. Fold the bodice side cut - checkpoint armhole. Pulled the top part of the sleeve with the distributed fit fold from the center of the crown half, equalizing the slices. Fold the sleeves at the bottom control point top part. Will Skolem pins the center of the top part of the sleeve with the shoulder seam of the product, the control point of the armhole, with the top part. Umatyvaet the sleeve is laid between the two threads, starting from the shoulder seam to the side of the shelves at 7 - 8 cm, then primetam the remaining part of the sleeve below the armhole on the crown.Excess hoses can be picked up at the seam. When Ironing sleeves and other small parts necessary to use a pad, covered with cloth or other soft cloth or narukana made of fabric and tightly stuffed with cotton wool.