Before proceeding to the treatment of the neck, it is necessary to check the shape and length of the sides of the neckline at right and left shelf. To do this, fold the product in half in the middle of the front and back, working the shoulder seams and the seam of the neck, Skolem pins, check and pruning so that both sides were the same. 

Types of openings can be varied: V-neckline, scoop neckline, figure, round, rack, ovate, scalloped, teeth, etc.

In the processing of filler-Skive shoulder seams treated slices, Ironing. For convenience, the machine grind the side seams after the neckline processed. V-neck can be treated podkralas, transverse or equity facing. The shape of the neck until the fitting is not cut. On fitting make a cut in the middle of the front or back (in style), went to the head, remove the product on the line with chalk to note the width and depth of the neck, laid the snare, equity or cross tack the piping to the front and to the back - Podkayne in the form of a cutout blade.

For proper podkraj piping to the neckline of the bodice will sprout peregrim in the middle of the back, aligning the shoulder seams and sections of Rostock, staple pins. For podkralas piping folded piece of fabric so that the fold of the piping and fold back have the same thread direction. Put obtachku on the back, combining bends with the width of the piping should be 4 - 6 cm more than the depth of the cut sprout and long shoulder cut into 2 cm (for seam). The width of the piping at the V neck should be the same with the facing of Rostock.

Grind the ends of obcutek at the shoulder cut in the middle of the front Ironing. Then protecive piping, paving the line on the snare from the shoulder cut on the sprout and the neck doing a double needle stick in the depth of the cut. Seam Ironing on the Board or the Board, Tognum piping towards the inside, releasing the roll from the side products by 0.1 - 0.2 cm, ormative, Ironing. The second section of piping machined zigzag stitch or filed by hand, bending the slice.

In the products of cotton fabric, the facing can be pritchatt on the machine, and wool and silk hand hemming stitches or to stitch, stepping back from the bend of 0.1 - 0.2 cm and attach to the back leg, that is, to attach the facing along the entire neck through 5 - 6 cm free thread (not grinding off to fit). 

Throat in products of transparent fabric (nylon, chiffon, Voile, Creperie) it is recommended to treat podkralas the facing. 

Seam grinding obcutek in the middle of the front was not visible, their shape must match the shape of the neck.

All other kinds of neckline is processed pokrainini obrazkami, adhering to the same rules as in the processing of the V-neck. It is necessary to observe the following rule: when podkre piping direction yarns within the unit and the facing must be the same.

When machining cut-outs, sealing the neck with a collar made of fabrics such as tricotin, crimplene, Jersey, knitwear, excluding piping from the main fabric, to cut out the cushioning material in the form of piping (1 - 0.8 cm less). The facing with prikladnoi retains the shape of the neckline, makes it tighter in fit, prevents deformation in the wash. 

The interlining fabric can be used in the processing of cutouts from different tissues, in addition to transparent.

Round - neck you can handle and a forward facing width 3 to 4 cm Obtachku will face to the front of the unit, equating sections of the piping to the product, PrimeTel, pristrochite and rasutim. Then treated like other cutouts.

Round neckline made of thin fabrics is treated most often rolikam. To do this, a forward facing width of 6 - 7 cm fold in half with wrong side inside, even the slices that sweep away, slightly pulling the string. Make the facing face to the side of the neck so that the fold was located in the side of the product, even slices, PrimeTel, slightly propositiva the neck in oblique sections, and protecive seam with the width of 0,5 - 0,7 see 

Will tognum the facing towards the inside, letting the roll of the piping is 0.5 - 0.7 cm, obetem the seam on the front side and prostrochite.

Ironing all kinds of cut to be careful to avoid stretching seams, it is best to iron on the Shoe.