Collars in a light dress and blouses can be integral, i.e., cut with the lower collars consist of two parts andsingle, and the edges of collars can be processed obecnym seam edging, seam itagiba or trimmed with ruffles, lace, edging, etc p. 

  Processing of one-piece collar. Collar bend along the middle (Fig. 62, a), put face inside, equating slices, and grind the ends (Fig.,62, b). The width of the seam is 0,5 - 0,7 cm.
If the upper collar is cut separately from the bottom, it fold the bottom collar, right sides inside, equatingslices, and grind the tips and go with fit top collar angles and radii. Joint width of 0.5 - 0.7 cm Sections of seams in the corners cut, leaving a seam allowance of 0.2 - 0. see the collars with scalloped edges on concave areas, sections of seams netscout to nadechka not it got to the line 0.1 - 0.2 cm; collar turn on the front side, corners and joints straighten and priorivet from the bottoma collar forming the edge of the top collar with a width of 0.1 - 0.2 see
In some cases, the collars with scalloped edges to manually spawn or on a special machine from the bottom of the collar for a distance 0.5 cm from the edge, forming the edge of the upper collar. 
In collars with a strip of fabric with one-side adhesive-coated strip applied adhesive coating on the underside of the lower collar so that the gasket edges are defended from the edges of the bottom collar about 0.5 - 0.7 cm, and stick an iron or press.
In a collar with a lining of cotton fabric or proklamelin strip applied to the underside the bottom of the collar and grind through the bottom of the collar. Products of woolen, silk fabrics and fabrics with a synthetic content fiber top collar with fold strip wrong side inside and metiaut (or grind off), landing on the top of the collar angles and radii. Then fold top collar with lower right sides inside and grind from the side of the strip, on the lineprimitivne and primaqiune strip to the top collar or departing from it towards mid on 0.1 cm Strip cut from the seam, leaving 0.1 cm, turn the collar on the front side, the corners and seams and straighten priorivet, forming, edging toward the bottom of the collar.
In the collar with frill frill impose the underside on the front side bottom of collar machined edge of the ruffles to the side mid lower collar, cuts call and pritachivajut side frills machine the line between the two lines or the second line form an Assembly the number of assemblies in the corners of the collar must be greater than at the edges. The lower collar is folded with the upper face parties inside and grind with the bottom of the collar, making the stitching in the seam of the ruffles primaqiune or departing from it by 0.1 - 0.2 cm inside of the mid-collar.
Turn the collar on the front side, the corners and edges straighten and priorivet. 
When connecting the collar with the neckline with piping on the shear stand from the top of the collar at a distance of 0.5 - 0.7 cm from the edge lay line (Fig. 62), forming a slack (overlap) the upper of the collar relative to the lower 0.1 - 0. see

  treatment is a collar consisting of two parts. Each part of the collar is treated separately, as well as the whole collar. The processed part of the collar placed machined ends butt and fasten hand stitches or machine stitching at a distance 0.5 cm from the edge (Fig. 63).
  Processing and finishing removable collar. Removable decorative collars, the upper collar can be cut tselnokrajnimi with the bottom or separate from the bottom of the collar.
If finishing collar one-piece, bend it along the middle face inward, equating slices, and grind the ends of the collar and the rack, leaving the rack neobychnym cut a hole with a length of 2.5 - 3 cm for 
screwing out.

If the upper collar is cut apart from the lower stack from the bottom, right sides inside, equating sections, and grind on all sides, leaving the cut stand a hole for screwing out. Cut seams in corners are cut, leavingallowance 0,2-0,Z see Through the left hole collar turn the front side, the corners and seams and straighten priorivet from the bottom a collar forming the edge of the upper collar. Left on the edge stand hole for screwing out zastrugivajut on the machine (Fig. 64, a) or manually sew hidden stitches. Cut the rack notto grind and a buttonhole on a special machine or to turn over (Fig. 64, b) depending on the falling of tissue.
  Processing a single collar. Slices single collars at the ends and departure can be processed inaccording to the model in the following ways: itagiba the seam closed cut, flat fabric edging seam with two closed sections and lace on a special machine. Treatment suture bodybu comply with using special devices.