Aprons
 

 
 Apron 1 (Fig. 140 a). Cut out of two parts: the cloth (Fig. 140) and the belt (Fig. 140 b). The apron is trimmed with lace around the edge and the cloth braid. The edge of the apron bends on the wrong side at 0.5 cm and scribbled on the distance of 1.0 cm from the edge of the lace (maybe you should baste). Then next to the first stitch of the second stitching hook tape on the panel, capturing the remaining free edge of the lace so that the bent edge of the cloth of the apron was located under the lace (Fig. 140 g).
Mark the middle of the upper edge of the cloth and the middle of the belt. Equating these marks, sew a waistband, folding his face with the back of the apron, the seam width 1.0 cm. Belt bend on the face, the transverse ends of the bends to the inside by 0.5 cm, loose side of the belt is 1.0 cm, namachivajut belt on the cloth, overlapping the first seam and the ends smatyvay. Fasten the belt line, at the same time adding his second line to the flag, and the same stitching stitch the ends of the belt, reaching for the drawstring (Fig. 140 d). Remove the basting, iron the apron.
  Apron 2 (Fig. 141 a). Consists of three parts: the cloth (Fig. 141 b), belt (Fig. 140 6) and stripes patch pockets (Fig. 141). The cloth of the apron dotted line to take the location of the patch pockets. Warp yarn patch pockets needs to be at the top of the pockets, protecting them from stretching.
 

The upper edge of the pockets to buckle for 1.0 cm, and then by 2.0 cm and secured with stitching. The lower section of impose face on the face of the cloth and pritachivajut seam width 1.0 cm (Fig. 141 g), and folded up the seam of primaqiune face again reinforce the stitching (Fig. 141 d). Then strip patch pockets divided into three parts, and outline of the line pin and sew the strip to the panels at intended lines at the top of the pockets make set triple stitching. The bottom and the sides of the cloth is treated with a seam in the hem (first bends of 0.5 cm, then 1.0 cm towards the inside and fix the hem stitching).
On the top slice of pre-lay clamps, directing or both outside or inside. Mark the middle of the belt and the middle of the upper edge of the cloth apron, combining these marks, the positioning face of the belt on the wrong side of the cloth. The free end of the belt bend in the face, bends of 1.0 cm, is applied to the seam protecive belt, slightly overlapping it. The ends of the belt run inside, aligning its width, namachivajut and fix the belt line, at the same time primativa his second line from the face to cloth. Remove the basting, iron the apron.
 

 Apron 3 (Fig. 142 a) with two tucks on each side at the waist, patch pocket. Trimmed at the hem with colored piping and lace. Consists of cloth (Fig. 142 b), the belt (Fig. 140 b) and add-on pocket. Prepared and plated pocket on the panel shown by the dotted line (Fig. 142 b). Cutting to the upper cut surface of the pocket to add 3.0 cm for processing in the hem. Remember that the warp threads on the pocket should go for the upper cut.Pocket with machined top cut edging at the sides and bottom strip of cloth, releasing at the beginning and end of the edging of 1.5 cm, bent edging, primetyvajut lace. First, the cloth of the apron is fixed inside the pocket of the edging (Fig. 142), the excess cut off.
Pocket namachivajut from the face, and then stitching on the edging and sew it round, making the tie at the entrance of the pocket (Fig. 142 g). The bottom of the apron is also a first edging, enclose the lace. Decorative stitching on the edging and pritachivajut and lace. Second line on bottom of apron reinforce the free edge of the lace so that the open cut strips of the edging left between the two lines (Fig. 142 d). The side apron is treated with a seam in the hem. Not to interfere with the thickness of the processed bottom, you can cut or handle side to treatment of NCDs.In this case, when participarii stripes fringing at the ends she podgibayutsya inside 0.4 - 0.5 cm, then fixed transverse lines (Fig. 142 e). Clips at the waist lay symmetrically, belt sewn on, as in previous models.
 

 Apron 4 (Fig. 143 a). Consists of cloth (Fig. 143 b), trimmed with braid around the edges. Instead of a belt used tapes. First, bend on the front side, 0,5 cm to the sides and bottom, namachivajut the slices then placed on top of the braid, primetyvajut and scribbled on two sides (Fig. 143). In the corners of the braid is laid pleat and secured in nastraivanii on the inner edge (Fig. 143 g). On the top slice of the fixed clamps at the waist.From the inside of the apron, also wrong sides, overlapping mid-panel and mid-braid (length to the belt of 1.2 - 1.3 m) primetyvajut and scribbled the braid (Fig. 143 d). Then she bent on the face and secured with stitching on two sides (Fig. 143 e). On the ends of the braid with a cloth on the top section made of setting the width of the braid.
 

 Apron 5 (Fig. 144 a). Consists of cloth (Fig. 144 b) and stripes patch pockets (Fig. 144). The entire apron is trimmed with piping, drawstring waist and the top of the apron used a prepared strip of edging (Fig. 130.)
Strip for patch pockets enclosed with top and bottom sides, lateral sides included in the edging of the apron. On the top of the pocket edging has a closed internal cross-section by the bottom may be open cut (Fig. 145, b). Banded strip combined with a panel of the apron, namachivajut on the sides, the hem in the seam edging prostrachivajut to cloth, in the middle of cross-stitching with bartacks at the top (Fig. 145) pockets again prostrachivajut to cloth.The strips of edging to the desired length for the drawstring at the waist are pre-attached to the marked place from the inside of a panel, flush with its cut. Then sheathe strip of cloth, cut at an angle of 45', all apron, except the upper edge, which is treated after the binding seam to the hem (podymaetsja first 1.0 cm, then 2.0 cm). On the face of unbend and drawstring at the waist and secured next to the seam of the edging (Fig. 145 g).In the ACC top weed out a prepared strip of edging to tie the apron at the top, the upper part probivaetsya and can be fixed by stitches to the edge of the border (Fig. 145 d).
 

 The apron 6 (Fig. 146 a). Consists of front and rear panels, wherein the neck (Fig. 146 b). On the front panel is a patch pocket. All sections of apron-treated strip of cloth, cut a 45°angle.
The pocket is also edged on the sides and bottom. When you cut the pocket should be added to 3.0 cm, which are for processing the top seam to the hem. (First podymaetsja 1.0 cm, then 2.0 cm). The direction of the warp threads - the entrance to the pocket to prevent him from stretching. Pocket edging, the edging strip is 1.0 - 1.5 cm beyond the pocket (Fig. 147 a) above, then the pocket bordered edging, it primatyvajutsja (Fig. 147 b). A pocket attached to the cloth of the apron wrong side up. Edging fixed transverse lines, cut off the excess (Fig.147), the pocket bent on the face and zastrugivajut on the edge of the border, and one line at the same time a pocket is sewn and fixed the inner part of the edging.
 

Prepare four strips of edging for drawstring waist, fixed at the marked locations. Shoulder cut zastrugivajut one side of the seam width 1.0 cm, sections were treated with a zigzag. Then cut around the neck and all the slices of an apron round (Fig. 148) and sew the second shoulder seam is treated with a zigzag. Iron the seam towards the rear of the cloth from the face by edging make bar tack stitching.
The apron can be sheathed and elastic, which is not drawn to edge and which is well laid out on the curves (Fig. 149).
Any apron can be processed seam to hem (hem is 0.3, the second 0.5 cm), then the top nastraivatsa delicate lace. In this case, when cutting, add seam allowance to the hem is from 0.8 to 1.0 cm (Fig. 150).