After treatment of the sides and the bottom connection of the collar with the neck lining is connected to the jacket. Lining precise, imposing it on the expansion of the product wrong side up, combine the side and shoulder seams and check the length and width. On podborta and the lining of the outline of the control line connector.

Then fold the lining side is facing the front of the jacket and primetyvajut at a distance of 0.9 cm straight stitches with a length of 1 - 2 cm to podborta and stand up collar, aligning the notch and the line of control marking on the lining and the garment. In the chest lining pokazyvaut 0.8 - 1 cm, while the gasket inner pockets are bent in the direction of lining products. Shoulder seams and the middle seam of the back lining combined with nasecki on the collar. If the back of the lining wider than the back of the top, lay it over top pleat seam by guiding the seam toward the left side of the back.

After primitivne lining pritachivajut on the part of the lining seam 1 cm wide, enclosing an adhesive cobweb from podborov (Fig. 59). A string of primitivne drop and make the notch at the seams podborov in the locations of the inner pockets. Turn the jacket on the front side. 

Podborta and collar spread, podborta namachivajut on shelves along the fold of the lapels and collar to the lower collar along the fold of the stand (Fig. 60, line 1). Then lay the lines on the inner edge of podborov (line 2), retreating from the seam of the lining protecive 0.3 - 0.5 cm.

The splice seam of the lining with the upper collar attached to the seam vrachevanie the bottom of the collar to the neckline sanding machine (line 3). The line lay from the top of the collar in the area between the shoulder seams at a distance of 0.1 cm from the seam connecting collar lining.

Jacket turn on the wrong side. The inner edge of podborov together with the lining attached to the side strip on the machine blind stitch or glue spiderweb on the press. Seams primaqiune of podborov to the lining and the ends of obcutek internal pockets between nasecki laid out and sent to the sides.

Then turn the jacket on the front side, call the shoulder and side seams of the lining and the jacket, check the length of the lining at the bottom of the jacket, placing the product face up. From the lining in the upper part of the jacket form the inlet equal to 1 - 1.5 cm, and release the sections of lining to 1 cm bent (swept) the bottom of the product. The excess lining trimmed.

Jackets with a vent in the lining of the back is cut on the edges right side slots, not reaching 1 cm to cross stitch, fastening the slot. Applied to the control line on the lining and vent for proper connection. Then remove the thread zamatyvala the bottom of the jacket and the jacket turn out on the wrong side. After that, pritachivajut the lining to the sides of the spline seam width 0.7 - 1 cm, combining the intended line. At the top of the splines lining sew a tuck and finish the above line incision 1.5 - 2 cm.

Lining pritachivajut to the bottom of the jacket from the lining seam width of 1 cm, starting from the line of stitching around the corners of the boards and smoothly translating the stitching on the lining (Fig. 61), combining lateral and middle .the seams of the lining and products. If the back of the lining wider than the back of the top, when participarii it over lay pleated on the middle seam, with the seam toward the left side of the back. 

Jackets with slit simultaneously grind the corners of the slots from the allowance for processing. Left corner grind the splines on the bottom line bending, reducing the line width of the seam 1 cm (Fig. 62, a).

When grinding the right angle slots, the allowance for bending the bottom at the bend lines bending and grind the seam width 0.5 cm (Fig. 62, b). 

Slices the bottom attached to the side seams and middle of the back of the product by car or five or six hand stitches blind stitch, or adhesive tape, which is laid over the seams from the wrong side of the allowance for bending the bottom at a distance of 0.2 - 0.3 cm from the edge. 

Then turn the jacket on the front side through the armhole. The corners of the slots straighten, to right of the slots at a distance of 0.1 - 0.2 cm from the edge of the lay line (Fig. 62).