The main purpose of lining is to close all the open seams of the product. Jackets on the shelves lining handle internal pockets with Velcro loops and buttons. 
Loops can be made from a special braid or strips of fabric with the help of devices installed on the machine platform in front of the foot. For loop braid folded in half, forming the curve of the triangle, which is secured by machine stitching.
The ends of the loop call, placed back to back and fasten on the sanding machine one line at a distance of 1 cm from the slices. Loop length (the distance between the clips) must be equal to the diameter of buttons plus a 0.5 cm

Internal pockets with two obrazkami of the main fabric

Lined shelves are scheduled at the auxiliary patterns line primaqiune of obrazek: two - along of the cut of the pocket, parallel to one another, and one across the cut side of the slice. The distance between the parallel lines is set in accordance with the width of the frame pocket. The width of the frame may be equal to 0.7 - 1.5 cm.
In the upper section of the lining of the pocket applied inside out down the valance of the lining fabric, the upper sections of the valance and lining equalize, and the lower section of the valance bends on the wrong side of 0.7 cm and scribbled on the distance of 0.1 cm from the fold. The valance on the left pocket scribbled cloth tape with a trademark, turning her slices of 0.7 cm Row pave 0.1 cm from the edge. The tape is arranged so that its side edges were equidistant from the lateral sections of the skirt and the upper edge at a distance of 1 cm from the upper edge of the valance. 
Then the front of the shelves lining is applied to the piping, right sides down and pritachivajut to the shelf, each facing a separate seam width 0.7 cm, the positioning slices of obcutek the intended lines. At the end of the pocket stitching done on the level of scheduled cross the line (CV. Fig. 39, a). The shelf between the cut lines.
To participate piping to the shelf and cut the shelf simultaneously, using two needle machine with a knife, which significantly reduces the time to perform these operations. The seam of the lower piping primaqiune straighten, unbend facing towards the inside of the lining, forming a frame, and pave the line at a distance of 0.2 cm from the fold (Col. Fig. 39, b, line 1). To cut internal piping pritachivajut the pocket lining seam with the width of 0,5 - 0,7 see
The seam of the upper piping bent towards the inside, forming a frame, equal to the width of the lower frame, place the facing on the upper edge of lining (with attached valances) and scribbled it on a distance of 0.2 cm from the fold (line 2), at the same time investing in the middle of the machined pocket loop. Then the edges of the upper and lower part of the combine and fix the front ends of pockets on the front side two back lines across the width of the part at a distance of 1 cm from the slices.
The ends of the pocket located on the side of the armhole, fasten to the underside of lining two back lines, smoothing the area of the lining, tightening of the piping and placing lines dolevik so that its second end reaches the armhole. The lining of the pocket sew a seam width of 1 cm 
At the ends of the pocket from the front side put tacking bartacking machine. Set have a distance of 0.5 cm from the lining from the armholes and at a distance of 1.5 cm from the side of the cut lining. The length of the clips of 0.7 cm, Middle of the tie should match the grub pocket.

Internal pockets with one facing of the main fabric

On the lining on the auxiliary pattern outlines the location of the pocket by two lines: one along the cutting pocket, the other across from the side of the slice. The valance scribbled on the pocket lining as described above.
Obtachku iron, folding along the middle underside and inside zastrugivajut at a distance of 0.2 cm from the fold (Col. Fig. 40, line 1) . The front of the shelves lining the facing is applied the bend to the bottom shelves and pritachivajut on the distance from the bend, equal to the width of the frame (0.5 - 1 cm)*. Line 2 should be held in an equity chalk line pockets.
Then treated the lining of the pocket placed on the shelf valances down and pritachivajut (line 3), while placing in the middle of a fabric strip folded right side out, and loop to front pocket. The distance between the lines of primaqiune piping and lining his pocket with the valance should be equal to the width of the frame. The lines should reach the transverse lines of the pocket.
The shelf between the cut lines. The turn pocket lining to the wrong side of shelves, to internal piping pritachivajut cut free cut lining pocket (see Col. Fig. 40, line 4).
Bend the frame to tighten the seam protecive lining pocket valance and fix the front end of the pocket on the front side two back lines across the width of the frame at a distance of 1 cm from the slices. The end pocket located on the side of the armhole, fasten to the underside of two opposite lines, straightening a corner of the lining and placing lines dolevik. The lining pocket, sew (line 5). 
----------------------------
* If the frame has a width greater than 1 cm, it is called the leaflets

inside pockets with leaflets from lining fabric

Pocket lining consists of two parts. On top of the lining pocket scribbled the valance. To the bottom of the lining of the pocket pritachivajut striped lining fabric seam width 0.7 cm at a distance from the cut edge of the lining pocket, equal to the width of the leaves in finished form. Pricechannel band round cut lining of the pocket, forming a sheet of a width equal to the width of the leaves in finished form plus 0.1 cm, place the leaves on a shelf on the planned line and pritachivajut at a distance of 0.1 cm from the seam primaqiune the strips to the pocket lining.The lining of the pocket folded in-side shelves and pritachivajut valance with lining pocket, seam 1 cm wide at a distance from the line of primaqiune leaves equal to the width of the leaves (CV. Fig. 41). At the same time under the valance with the lining of the pocket pritachivajut enclose and cloth tape, positioning it in the middle of the length of the lines.
The ends of the lines of primaqiune the leaves on the valance should be placed parallel to the side cut of lining shelves. 
Further, the pockets are treated the same as a pocket in the frame with one facing of the main fabric. 

Darts and seams of lining 

Tuck begin to stitch from the armhole seam 1 cm wide; below the waist line seams gradually nullify, to below the ends of the incision 2 cm 
To the shelves and the back lining pritachivajut extensions, paving lines from the supers.
The middle sections of the back to grind, starting from the neck. The side sections of the backrest and shelves to grind of the back side, aligning the notch; the left side seam perform bottom-up right - down. Shoulder seams sew through Posiva back. Joint width 1 cm 
the Hanger is manufactured using the installer or using a special tape. To cut the neck lining the ends of the hanger pritachivajut triple reverse stitching, placing them at a distance 3 - 3.5 cm from middle seam of the back. The length of a hanger 7 - 8 cm.
Lining priorivet inside out on the table covered with a cloth. Side and shoulder seams, Darts iron in the back side, at the same time priorivet interior pockets. The seam of the back iron towards left side. 

QUESTIONS FOR REVIEW 

1. In what sequence handle internal pockets with two obrazkami? 
2. What parts are needed to handle internal pockets with one facing of the main fabric? 
3. Different processing internal pockets with one facing of the main fabric from the processing of pockets with leaflets made of lining fabric?
4. How to sew Darts and side sections of the lining? 
5. The sequence in which perform the wet-heat treatment pads? 
6. How sew shoulder seams of lining?