DRESSES FOR teenage GIRLS

CONSTRUCTION DRAWING BASIC PATTERNS DRESSES FOR TEENAGE GIRLS 

in the drawing of the pattern removed following measurements (in cm): 
a semi-circle neck ....... To 17.5 
>> breast ...... 44 
>> waist ...... 36 
" hips . . . 48 
back Width.................... 8 
back Length to waist ....... 36 
" dresses..................... 95 
shoulder ..................... 12 
Allowance for loose fit at the chest line should be at least 5 see 

the plan 

Draw rectangle АА1НН1 (Fig. 255). The vertical line of the rectangle is equal to the measure of the length of the dress: an=А1Н1 = 95 cm 
Horizontal line rectangle is equal to the semicircle of the breast, plus 5 cm for loose fit: AA1 = НН1 = 44 + 5 = 49 cm. 
The depth of the armhole. From point A to defer down vertical 1/3 semicircle chest plus 4 cm and place the point of G: AG = 44: 3 + 4 = 18,7, see 
the line of the circumference of the chest. From point G to spend right a horizontal line to the intersection of the vertical and put the point G1.
The waist line. From point A to postpone upside down measure the length of the back to the waist line and put the point T: at = 36 cm
From point T to hold right horizontal line to the intersection of the vertical and put the point T1.
Line of the hips. From point T to postpone down vertically 18 cm and to put the point B. From point B to hold the horizontal line to the right to the intersection with the vertical and put the point B1. 
The width of the back. From point G to defer to the right of the circle's circumference chest width the back is about 1/3 of the semicircle of the breast plus 3 cm, and put an end G2: ГГ2 =44:3+3 = 17,7 = 18.
From a point G2 to hold up the vertical line to the intersection with the horizontal and put an end A2. This line divide into four equal parts. 
The width of the openings. From point G2 to defer to the right of the circle's circumference chest width armhole, equal to 1/4 of the semicircle of the breast, and put an end G3: Г2Г3 = 44: 4 = 11 see
From the point G3 to hold up a vertical line to the horizontal and put an end A3. From the points G2 and G3 to delay down vertically for 1 cm and put the points M and M1. These points to connect with a straight line. From the point M to postpone the right 1/3 of the width of the openings, andto put the point G4: MG4 = 11: 3 = 3.6 cm. 
Through the point G4 draw a straight line up the length of 0.5 cm down to the intersection with a horizontal line at the bottom of the dress. At the intersection with the waistline to put the point T2, with a line of hip point B2, with the underline point H2. 

Construction drawing of the back

The width of the blade. From point A to defer to the right horizontally the width of the sprout is about 1/3 of the semicircle neck plus 0.5 cm and put in point a is: AA = 17,5: 3 + 0,5 = 6,3 cm 
Height. From point a swipe up vertical line length of 1.5 cm and place the point A1, then the line continue up a further 0.5, see 
the Line Rostock to hold a smooth line connecting the point of 0.5 A.
Shoulder line. For slope of shoulder from the point A2 to postpone down vertical 1.5 cm From point A1 to hold the right point and 1.5 line equal measure the shoulder length plus 1.5 cm on the landing shoulder seam to loose-fitting blades, and put a point P: а1П = 12 + 1,5 = 13.5 cm 
Cut а1П divided into 3 equal parts and from a point 0.5 of the right to hold a smooth line that is tangent to the first point of division.
Line openings. From point M draw a line 2.5 cm long, dividing the angle in half. The line of openings to hold from the point P to the point of 2.5, the tangent А2Г2 to the line between the middle and lower points, and then to the point 0,5. 
Line the side seam. Line of the side seam at the waist has a tuck. 
To calculate the depth of the Darts at the waist line it is necessary to find the difference between width of the product and the measure of the semicircle waist with the addition on a free fit 2 cm: 49 - (36 + 2) = 11 see 
Found difference divided by 4 (number of Darts on the waist): 11 : 4 = 2.8 cm
The depth of the side tuck is 2.8 + 1 = 3.8 and = 4 cm 
the depth of the tuck at the back is 2.8 cm 
The depth of the first tuck on the waist line of the front is equal to 2.8 also see the Depth of the second tuck on the waist line of the front is equal to 2,8 - 1 = 1,8 = 2 cm 
To draw a line of the side seam in accordance with the calculation it is necessary from the point T2 to delay the left on line waist of 2 cm in this point to connect a straight line with a point of 0.5. Then point 2 through point B2 to continue a straight line to the intersection with the lower horizontal line.
Line the bottom of the dress. From point 2 (line waist) line side seam to postpone the skirt length - 59 cm (the difference between the standards of length and length of back to waist): 95 - 36 = 59 see 
Point 59 to connect a smooth line with lower horizontal line. 
Tuck on the back. From point T to postpone right 6.3 cm (width of Rostock). From point b. to defer to the right depth tuck 2.8 cm; split 2.8 cm in half and through the point of division draw a vertical middle linetuck, not bringing it to 6 cm before the line ГГ2 and continuing down to 10 cm. Point b and 10 
connect the straight lines with points b,d and 2.8.

Construction drawing of the front 

Length of the front. From point A1 to continue up the vertical line. From the point G1 to defer up vertical lines 1/2 of the semicircle breast and put an end to: Г1В = 44: 2 = 22 cm
From point b to hold the left horizontal line with a length of 12 - 15 cm 
Width of the neck. From a point to the left horizontally to postpone the segment BB1 equal to the width of Rostock: BB1 = AA = 6,3 cm 
The depth of the neck. From point b to delay vertically down 1/3 the semicircle of the neck measure plus 1 cm and put an end B2. BB2 =17,5:3+1 =6,8 cm
From the point In to draw a line dividing the angle in half, length 6.3 cm (mouth width) and put the point B3 . Point B1, B3, B2, connect a smooth line - the line of the neck. 
Length shoulder to tuck. From point B1 to defer to the left horizontally 3 cm. From the point G1 to the left in a straight line to delay the distance from the middle front to the end of a chest tuck - 8.3 cm (sum of the width of the neck and length shoulder to tuck minus 1 cm) and put an end G5: Г1Г5 = 6,3 + 3 - 1 = 8,3 cm
Points 3 and G5 to connect a straight line. From point 3 to delay down for the line 1 cm Point 1 and B1 connect direct line, which will cut the shoulder to tuck.
The depth of the tuck. Point 3 to connect the auxiliary line with the top the breaking point on the line А2Г2. The width of the openings MM1 split in half and the dividing point up to hold the line to the intersection with the upper line, and at the intersection of the supply point P1. From the point P1 to defer to the right 1.7 cm (1/3 of allowance for loose fit at the chest line). From the point of 1.7 to postpone 9 cm (length of shoulder-to-measure minus 3 cm is cut from the shoulder neck to tuck): 12 - 3 =9 cm 
From point G5 through the point 9 a straight line is equal to the right side of the tuck, and put the point P2.
Length from shoulder Darts to the armhole. From the point P1 to postpone down vertical 3 see Point 3 and P2 connecting a straight line. From point P2 to delay the left the leg length of 9 cm and put the point P3. 
Line the arm openings. From point M1 to postpone upward 1/4 line А3Г3 and to put the point About which to connect straight auxiliary line point P3. This line is split in half and the points of division to postpone 1 cm right From the point M1 to draw a line of length 2 cm, dividing the angle in half.
From point M1 to postpone the left horizontal cut, equal М1О, and to put the point O1. The line of openings to hold a smooth line through the points P3, 1, a, 2, O1, and 0.5.
Line the side seam. From point T2 to delay right 2 cm, i.e. half side tuck. To connect with a straight line points 0.5 and 2. From point 2 through point B2 draw a line to the bottom horizontal line. 
From point 2 (at the waist) to lay lines of the side seam the skirt length - 59 cm, equal to the length of the side seam on the back. 
Clarifying the waist line. From point T1 to postpone down 1 see Points 1 and 2 on the line of the side seam to connect a smooth line.
Clarification to the hips. From point B1 to defer down vertically 1 cm point 1 and B2 to connect a smooth line. 
The bottom line is. From the point H1 to defer down vertically 1 cm and points 1 and 59 to connect a smooth line. 
Darts at the waist line. Front of dress has two Darts on the waist line; the distance from the middle front to the first tuck on the waist line anyway the distance from the point G1 to the point of the G5 minus 1.5 cm: 8,3 - 1,5 = 6.8 cm = 7 see
Points 7 and G5 to connect the auxiliary straight line. From point G5 to defer down by a line drawn 6 cm From point 7 to defer 2.8 cm to the left of Point b and 2.8 connecting a straight line. The depth of the Darts divide in half and from the dividing point to hold down vertical average the line tucks a length of 10 cm Point 10 connect points 7 and 2.8 straight lines. 
Waist line from point 2 to point 2,8 to share in half and through the point of division draw a vertical middle line tuck, not bringing it to the line ГГ1 6 cm and continuing down to 10 cm.
From the point of division to be postponed left and right 1 cm (half the depth the second tuck). Point b and 10 connect the straight lines with points 1 and 1 on the waist line. 

Construction drawing of a sleeve 

For construction drawing the main pattern of the sleeve taken measurements in inches: 
sleeve Length ...................... 58 
wrist Circumference............ 19 
Draw a rectangle АА1НН1 (Fig. 256). 
The vertical lines of the rectangle equal to the length of the sleeve: an =А1Н1 =58 cm
To determine the length of the horizontal lines of the rectangle should to 1/3 semicircle breast add 4 cm and are all double: AA1 = НН1 = (44 : 3+ 4) 2 = 37,4 cm
Line height of the crown. From point A to defer down vertically 3/4 of the depth of the armhole and put the point R: AR = 18,7 : 4 x 3 = 14 cm
From point R to right, hold the horizontal line to the intersection of the vertical and put the point P1. 
Horizontal line AA1 be divided into four equal parts and from each the points of division to spend down vertically straight up to the intersection with the lower line the sleeves, put the points H2, H3 and H4.
In the middle of the top horizontal line to put an end V.
Line of lifts the shoulders. Connect the straight auxiliary lines point Inwith the points P and P1. On the line crossing the elbow to put point On, and with the front line of the bend - point O1. Line VO1 and VO split in half and from the points of division to restore the perpendiculars length of 1.5 cm (to line VO1) and 2 cm (line IN). Cut О1Р1 split in half and the dividing point to hold down the perpendicular equal to 2 cm.
From the point About to defer up vertically 1.5 cm Line OP to divide into two equal part and a lower part in half again. From the bottom of the dividing point down to carry out the perpendicular length of 0.5 cm 
the line of the top part of the sleeve to pass through the point P; 0,5; the breaking point; 1,5; 2; V; 1,5; O1; 2; R1 a smooth line, as shown in the drawing. 
Line the bottom of the sleeves. To defer up vertically 1 cm from the points N, N3, N1, and 2 cm from point H2. Line the bottom of the sleeves to hold a smooth line connecting the points 1, H4, 1, 2, 1. 
Cuff. To build a rectangle that is 4 cm vertically and 20 cm horizontally.