Such an original blouse with a nice collar will decorate your wardrobe (Fig. 108). You can wear not only on secular Raut, but also to go to her for a meeting with friends in cafe or restaurant.

The main advantage of this blouse is the practicality, convenience, and elegance. Very interesting contoured lines of this blouse. It with cap sleeves, bottom seam which starts from the waist line. Vertical relief lines are shifted in the direction of the arm openings. In the upper part of the sleeve is laid in soft folds. The special charm of the blouse give a fur collar and cuffs.

For drawing shaped lines you can use the drawing basics dresses with cap long sleeves. Lower cut not processed. A line of seats side seam, continue below the waist to 2 cm and place the point T2. Prepare the drawing basics backrest. To process the lower seam of the sleeve point T2 connect the dotted line with the point M1.

Divide this line into three parts. From the first point located closer to the side seam, measure up 5 cm and label it with the letter E. fill in the seam line of the lower sleeve through the points M1, e, T2. Build around this point one or two Darts a depth of 2 cm and Then connect the points T2 and T a smooth line. Т2Т is the waist line.

For building line of the lower sleeve seam line of the front connect point T2 with the point M2 with a dotted line and divide it into three parts. From the first point located closer to the side seam, measure up 5 cm and label it E1. Through the points T2, E1, M2 outline line the bottom seam of the sleeves front. Close the Darts on the line of the bottom seam of the sleeve backless.

Compare the length of the lower joints of the back and front.

The result of the comparison, add or remove the line to the bottom line at the point M2.

Indicate a new point M4. Connect a smooth line point T2 and T1. Get waist line of the front Т2Т1.

When applied to shaped lines, be very careful. To describe the shapes of the lines, follow the next build.

To build the neckline of the back gate from the point A1 to the right, measure along the line of inclination of the shoulder 2-3 cm and mark the point C. Connect point C with point A concave line.

For this line the slope of shoulder, measure from the point C to the right 6-8 cm and mark the point R.

From point T at the waist to the right, measure 8-9 cm and mark the point P1. Points connect with a straight line.

The shoulder tuck, transfer into a relief line. To accomplish this transfer, measure from point R to the right of the line of inclination of the shoulder shoulder tuck depth of 1.5 cm and place the point P2. On the down relief measure 7-8 cm and place the point P3. Connect the points P3 and P2 by a straight line, continue to build on the crown of the sleeve above the line of inclination of the shoulder at 3-5 cm and place the point P4. Draw a new line the upper seam of the sleeve, connecting points P4 and M.

Tuck waist backless put in a relief line. Follow this construction in this way: from the point P1 to the right, measure at the waist line a deep tuck backrest, but not more than 3 cm, and from the chest line down relief 2 see Connect these points.

When applying the style lines on the front start with the lines of the cutout gate. To do this, from the point A6 to the left of the line of inclination of the shoulder, measure 2-3 cm Denote the resulting point C1. Through this point draw a vertical line. From the point A7 down through the middle of the front, measure 6-7 cm and place the point C2. Through the point C2, draw a horizontal line. Measure 2.5–3 cm on the bisector of the angle formed by these lines and put a point C3. Through the points C1, C3, C2, make the cutout gate.

Apply relief the line of the bodice. To do this, from the point C1 on the line of the slope of the shoulder to the left, measure 6-8 cm and place the point P5. Waist to the left of the point T1, measure 8-9 cm and mark a point P6.

The resulting points P5 and P6 connect with a straight line.

Get chest tuck in the vertical shaped line. Swipe through the point u a horizontal line left until the intersection with the relief line and mark point C1. Note from point R5 to the left of center, arc, is equal to the depth of the chest tuck. From the point C1 to the arc tangent swipe, continue above the line of slope of shoulder, 5 to 8 cm and place the point P7. Draw a new line the upper seam of the sleeve. For this connect the dots P7 and M3 in a straight line. Remove brisket tuck in shaped line. From the point P6 to the left on the waist line measure the depth of the inframammary tuck.Then from the point C1 to the down relief put 3 see plotting points connect with a straight line.

The drawing of the collar make your own. Draw a straight angle with vertex at point O with the sides of an angle of arbitrary length.

From point O up measure 20-30 cm (point B1), the right — half of the length of the circumference of the neck (point b).

Swipe through point B1 horizontal line of a long line of S at 8-9 cm and get the point B2. Connect the dots B2 and V. This is the line of the collar.

The line OV1 measure up to 4 cm, the resulting point will connect with a point In a convex line. This is the line terminations of the collar to the neckline.

Continue the line OV1 above the point B1 5-6 cm, and from the point B2 down to the seam line of the collar, measure 2, see Connect a convex line up the points obtained, and get a line the departure of the collar.

A good addition to this model is a strict skirt-Maxi.