The basis of the drawing of this model (Fig. 70) take the previous pattern. Lay the pattern back and front on a piece of paper, trace them and, if necessary, adjust the length of the robe.

Back. Sprout. Extend the right line of the shoulder cut. Expand Rostock 1-2 cm compared to the previous pattern and reduce its depth of 4-5 cm and Then fill out a new sprout of a smooth concave line (Fig. 71).

Flirty. From a new line of sprout put in 10-13 cm along the lines of the mid-back and shoulder cut. This will be the width of the yoke. Plotting points join with a smooth curve, parallel to the line of Rostock.

Shoulder cut. From the point 10-13 cm along the line of the cut yoke put down a length of 2-3 cm With a ruler connect the obtained point by point 1-2 cm

Armhole. From the beginning side of the slice contour of the pattern is put 2 cm up. Right from marked on the circuit pattern of the openings along the line of the cut yoke put 2 cm and label the resulting point as a reference.

Connect it with the new start side of the cut a smooth curve, parallel lines of openings of the circuit.

The section line. Divide the Breasts in half. From the line the lower edge of the yoke and draw a vertical line passing through the obtained point. This point control.

Before. Apply a line yoke, armholes, and cut in the same way as in the drawing of the back, reducing the depth of the neck 3-4 cm Close the tuck in side. To do this, draw a line from the yoke to the center of the tuck. When cutting you will need to cut the pattern along this line and slide it to the width of the closed tuck. Thus, there is a new tuck. The point of intersection to the armhole yoke and cut lines from the bust line mark as a reference.
 

Fig. 71. Drawing style lines of the gown

Fold the fabric lengthwise face inward. Lay the pattern back and front means to bend. Extend the pattern back along the line of incision of 5-7 cm, and the pattern of the front — to 6-8 cm (Fig. 72). Make sure that the control points were located strictly on the same horizontal. 

Make allowances for seams and hemming the bottom. If you don't have enough fabric, you can sew the details of the yoke in the middle.

The seam allowance in the middle of the yoke should be 1, see also Cut piping (slant or Podkayne) width 2.5–3 cm for the treatment of openings.

Raskroyu fabric, mark the middle of the major parts (back, front and yoke) slip-stitches. Route copy the seam reference points of a coquette. Then sew to the bottom of the wedges.

If the internal yoke cut, sew details and Ratatouille seam. Sew shoulder seams of yoke (first outer, then inner) bridging seam. Seams carefully Ratatouille. Then fold the outer and inner yoke right sides inward so that their mid-and shoulder seams match.
 

Fig. 72. Layout of patterns on fabric and cutting the dressing gown

Fasten the parts with pins, baste and sew around the cutout for the neck. Sew the sections of the seam to the inner yoke at a distance of 0.1–0.2 cm from the line. Remove the yoke on the front side, straighten and prometeia seam. Assemble the upper sections of the back and front (you can hand-stitch). Evenly distribute the Assembly. Sew the side sections of underwear lapped seam sapacheva to the back, and treat prepared by the armhole facing (the front side).

Attach the inside of the yoke facing the wrong side of the front and back slice to slice.

The middle control point on the line of openings must coincide. Baste and sew the details, then zautyuzhte seam toward yoke.

For finishing the yoke, use the frill (you can also smocked lace). Baste it to the outer yoke through primaqiune to the lower parts of the robe. It should be remembered that the line of primaqiune ruffles should be about 1.5 times as long as the line of primaqiune yoke.

Fold the seam allowance on the bottom of the outer yoke and using pins to fasten it to inner so that means, the shoulder seams and control points on the lines of the openings coincide, then keen and Topstitch. Joint width should be between 0.1 and 0.2, see

the bottom of the negligee hem seam itagiba with a shut cut.

The gown can be made more open if performed on the straps.