The drawing skort (Fig. 89) in addition to the standards required for the basic patterns, you'll need another way-Sun (27 cm). The basic circle pattern front and rear panels.

The extreme points of the lines in the middle, side cut, top cut and thighs indicate the same letters as in the main drawing.

The rear half of 

an Average slice. From the point T2 down the line side of the cut put the cut equal to the height of the seat minus 1, see Check point and I swipe across it a horizontal line to the intersection with the middle of the rear and front panels. The intersection points mark the letters H1 and H2 (Fig. 90).

Continue received line to the left for a distance, equal to 1/5 of the measurements of poluobhvat hips with the addition of free customized fit plus 1, see Check point Я3. Thus, Я1Я3 = 0.2 x (POB + PB) + 1 = 0.2 x (53 + 2) + 1 = 12 cm.

From point T up put the cut, 1/10 measurements of poluobhvat hips minus 2 cm Label of the received point letter T3.

Divide Я1Т3 cut into 3 parts. Label the lower point division H4. Find the bisector of the angle Я4Я1Я3 and put it from the point H1 segment equal to 1/10 of the measurements of poluobhvat hips. Put a point AM5. Then connect the dots Я3, AM5 and H4 smooth concave line.

Stepper cut. From the point Я3 restore the perpendicular to the extension of the line of the hem and mark the resulting point letter N5. To the left of this point put a horizontal line equal to 1.5 cm, Connect the point 1.5 cm from point Я3 with a ruler.

The side cut. To the left of the point D2 on the line of the bottom put a cut length of 2 cm, Put a point H3 on the line and connect it with the point B2.
 

Fig. 90. Drawing style lines skort

The front half of 

an Average slice. Continue the line Я3Я2 right on the cut, equal to 1/5 of the measurements of poluobhvat hips with the addition of free customized fit minus 1, see Check point AM6.

Divide Я2Т1 cut into 3 parts and label the lower point division letter Я7. The bisector of the angle Я7Я2Я6 from the point H2 postpone the cut, 1/10 measurements of poluobhvat hips minus 1, see the resulting point label Я8. Connect the dots Я7, Я8 and AM6 smooth concave line. Shorten the line in the middle 1 cm of the point T1.

Stepper cut. From the point AM6 restore the perpendicular for a continuation of the bottom line. Mark the resulting point h6. To the right of the point N6 put a horizontal segment of length 1.5 cm

, Connect the point 1.5 cm from point AM6 with a ruler.

The side cut. To the right of point N2 of the bottom line put 2 cm and place the point H4. With a ruler connect the dots D4 and B2.

If for sewing pants skirt you choose fabric with a width of 80-100 cm, you'll need three lengths of the product plus 6-8 cm fabric width of 140 cm need two lengths plus 3-4 cm.

Culottes can be inverted pleat in the middle front and back halves, as well as flared. When cutting skirts trousers with inverted pleats (Fig. 91) I need to cut patterns of the front and rear halves along the lines of the middle and push them to a depth of pleats (16-24 cm). Reduce the depth of folds along the hem of 2-3 cm from each side. Through the points H4 and Я7 to the waist line guide line of the crease.
 

Fig. 91. Cutting skort with inverted pleats and back half; b — front half

If the fabric is thick, the top of the crease to cut. When cutting a flared skirt- pants (Fig. 92) it is necessary to extend the Darts at the waist to the hip line. Then you need to make slits from the lower edge to the center of the Darts. Close the Darts at the waist. As a result, the pattern will slide out of the bottom line.

Lay the pattern so that the lobe filament was held concurrently stepping the slice. Give the seam.
 

Fig. 92. Cutting flared skirt -pants and the back half; b — front half

Lay "traps" (copy seam) along the contour lines of the patterns and the upper bends of the folds. Baste and sew Darts. Baste the side sections. On the left side will be handled clasp, so the seam should not reach the upper edge on 16-20 see Sweeps stepper sections of the left and right halves. The average front and average rear sections fasten with pins, then baste.

Lay and Sametime folds, baste the waistband. Then do a fitting. Sew the sections and astrocyte pleats from the waist to the points H4 and Я7.

Last treat the clasp and the upper and lower sections. Tutuila skirt -pants.