Distinguish between aprons in different designs: single cut, cutting at the waist, etc., Drawing apron with cap straps and zipper in the middle back you can build on the basis of patterns nightgowns. For finishing bottom you can use a narrow Ruche.

To construct a grid drawing of the apron (Fig. 73), you will need to take the following measurements (in cm):

— DST (41);
— DPT (44);
— the Posh (18).

Back. Draw a straight angle with vertex at point a and the parties directed to the right and down.

Line middle vertical side of the angle.

The waist line. Aside from the point in the middle of the back vertical line equal to the length of the back to the waist (in this case, 41 cm). The resulting point label with the letter T from it and spend a horizontal line to the right.

Length. From T point down the line the middle of the back put a length of 20-22 cm and put the H-point.

Width. From point T up through the middle of the back put a segment of length 5 cm set point T1, postpone the right of it a horizontal line with a length of 14-15 cm and place the point T1. Right horizontally from point T postpone 19-21 cm, and denote the resulting point by the letter T.

the cut Side. From point t draw the vertical down line with a length of 20-25 cm and put the point H1. Then set aside the right of point H1, a horizontal length 3 cm and mark the point N2. With a ruler connect the points t and H2, the resulting line will continue to 10 cm in

the Lower section. Connect the smooth line of the H-point and 10 cm

neckline — horizontal side of angle A.
 

Fig. 73. Drawing apron with cap straps and zipper in the middle back and back; b — before

Sprout. To the right of the point A on the neckline put a horizontal line. Its length should be equal to 1/3 of poluobhvat neck plus 3-4 cm, in this case about 10 cm Put a point R.

from point Down in the middle of the back set aside 16-19 cm and place the point G to the Right of point G put a length of 7-9 cm, the resulting point connect the auxiliary line with the point T1. Auxiliary split line into 3 parts. Right from the top of the division, restore the normal length of 1.5–2 cm, and bottom — 1-1,5 see Connect the dots R, 1.5–2 cm, 1-1. 5 cm and T1 smooth concave line.

Allowance for the length of the clasp. To the left of the point T1 and N put 2-2,5 cm and spend a horizontal line parallel to the middle of the back.

Armhole. To the right of the point P put a horizontal segment of length 3.5–4 cm, then move the resulting point down 0.5–1 cm This will be the bevel of the shoulder.

Connect the dots of 0.5–1 cm, T1 and t a smooth concave line.

Before. Draw a straight angle with vertex at point a and the parties directed to the left and down.

Line middle vertical side of the angle.

The waist line. From point A through the middle of the front set aside a period equal to the length of the front to the waist (44 cm). Mark received a dot letter T, and swipe from it by a horizontal line to the left.

Length. From T point down the line mid front put cut, is 45-50 cm and place the H-point.

Width. From point T up through the middle of the front put a length of 6-8 cm Put the point T1. To the left of it put a horizontal line with a length of 17-19 cm, and from T point — 24-25 see dot T1, and so

the Side cut. From point t draw the vertical down line with a length of 22-25 cm Put the point H1 and the left of it set aside 5-6 cm Denote the resulting point H2. With a ruler connect the points t and H2, and then continue the line down to 8-10 cm

the Lower section. Connect the dots of 8-10 cm and N a smooth curve.

Neck line — horizontal side of angle A.

the Neckline. To the left of the point And the line of the neck put a period equal to 1/3 of poluobhvat neck plus 3-4 cm, Put it In and connect it to point T1 smooth concave line.

Armhole. To the left of point V at the neck line put a segment of length 3.5–4 cm, then move the resulting point down by 0.5–1 see Connect the dots of 0.5–1 cm, T1 and t a smooth curve.

If fabric width is 60 cm, take two lengths of the front apron. If the material has a width of 80 cm, you will need one length of the front apron and 30 cm.

Fold the fabric lengthwise face inward. The pattern backless place so that the distance from the edge of the seam allowance to the length of the fastener to the fold of the fabric was 3.5–4 cm. This distance must be left for the allowance for processing the setting of the fastener. Make a seam (0.5–0.8 cm in all sections). Of basic or finishing fabric cut bias piping that you'll need to handle the arm openings and neckline. Run along the contour lines of the pattern copy the seam. Mark the middle of the front of the intermediate stitches. Treat the setting of the fasteners are made when cutting the seam allowance.Alternatively, you can use the equity obtachku. Hem the seam allowance or the seam facing itagiba with a shut cut.

Shoulder and side sections of the back and front sew the lapped seam (zapisyvaite to the back). Treat the underarm and the neck pre-prepared a forward facing. On the left side of the zipper sew hanging loops, with the right buttons.

The bottom of the apron seam treat itagiba with a shut cut. You can also turn over it as underarm and neck for the neck, or obtusate. In addition, you can pritchet to the bottom of a narrow frill.