Offer the jacket (Fig. 114) tapered at the waist, and the corners of the shelves are cut, which gives it elegance. Jacket length on the back — 54-55 cm

For jacket required suiting a length of 150 cm and a width of 150 cm, lining fabric length 130 cm and 140 cm wide, interlining G 405, 4 large and 2 small buttons, Raglan shoulder pads type.

 Drawing-based transfer on a large sheet of paper and apply a contoured line cut-off corners and a tapered waist line.

Pattern pieces on the drawing number:

— middle part of the back, kreena with back half sleeves (2 details);
— the middle part of the shelf, kreena with the front half of the sleeve (2 pieces);
— the side shelves (2 pieces);
— side part of the backrest (2 pieces);
— podbot (2 pieces);
— the facing of the neck (1 piece);
— burlap pocket (4 parts);
— a facing the bottom (4 parts);
— PATA (2 parts).

Cutting

build the drawing pattern of the jacket.

Vykroyte 4 piping length of 14 cm and a width of 3 cm each, 4 burlap pockets, each with a length of 10 cm and a width of 14 cm; and 2 PATA, each with a length of 4 cm and a width of 6 cm (ready 3 cm).

The details of the pattern lay out on fabric and vykroyte, leaving allowances for seams. Facing the bottom of the backrest (item 8) find one detail without the Princess seams. Parts 1-4 vykroyte also from lining fabric minus the width of podborov and obrazek.

Processing sequence

1. Start sewing from the back. Sew middle seam of backs. PATA fold in half lengthwise, clean witchita long and one short side. Witchita the short side corner. Keen PATA on the middle backrest in targeted areas between the cross marks.

2. Sew Darts on front sides of the shelves, and then sew the side sections and the bottom seams of the sleeves. Sew shoulder seams and upper sections of the sleeves to the level of the slots.

3. Sew the sides of the shelves to the middle parts of the back up area. Sew the side pieces of the back to the middle parts of the back exactly to the mark.

Make the notch at the ends of the lines in the corners on the allowances of the seams of the middle parts of the shelves and back. The sleeve is strictly sew on labels affixed when executing the drawing pattern.

4. Make Welt pockets. This will strengthen from the inside line of the cut on the shelves strip strip width of 4 cm Pin to the line of the cut piping, pre-folded them with shelves, right sides and sew at a distance of 0.5 cm from the cutting line. Cut shelves between the lines. At the end of the stitch seam nadsekite obliquely. Slotting shelves, do not damage the piping. Ratatouille allowances of seams. Sametime piping on the wrong side and go around them slices. Straighten each in the form of a flat box.

5. Put one burlap under the hole. Send it up. Sew with the front side facing the bottom exactly in the seam of primaqiune when you sew the burlap. Then fold the burlap down. Place and sew the second sacking of the pocket in the seam of the upper piping primaqiune.

Remove the triangles at the ends of the holes on the wrong side and Topstitch on the facing. Prostrochite from the ends of the top line to the ends of the bottom line. Trim and align the burlap pockets, and then sew them with each other.

6. Sew podborta with the neck facing the back and facing down. Witchita podborany and obrazkami the bottom of the jacket, sides and neck. Sew podborta to the hem.

7. When sewing the sleeve hem the bottom. Sew longitudinal sections of piping slots and the stock slot. In the upper part prostrochite across. Sew the slot for the small buttons.

8. Sew shoulder pads and connect the jacket with lining. Prometiste loop in the marked places on the right shelf for large buttons. PATA attach small buttons to the back.